Cord from being disconnected accidentally. (p. 18), 18 chapter 1 outputting sounds, Lock – Roland V-Bass VB-99 User Manual

Page 18

Advertising
background image

18

Chapter 1 Outputting Sounds

*

The GK cable is a locking cable. When disconnecting the cable, do

not pull on it with undue force, but instead release the lock and

gently disconnect the cable. You can disconnect the cable simply and

easily by holding down the locking portion with your finger and

gently pulling on the plug.

921

*

To prevent malfunction and/or damage to speakers or other devices,

always turn down the volume, and turn off the power on all devices

before making any connections.

932

*

Place the AC adaptor so the side with the indicator (see illustration)

faces upwards and the side with textual information faces

downwards.

*

The indicator will light when you plug the AC adaptor into an AC

outlet.

924

*

To prevent the inadvertent disruption of power to your unit (should

the plug be pulled out accidentally), and to avoid applying undue

stress to the AC adaptor jack, anchor the power cord using the cord

hook, as shown in the illustration.

fig.CordHook.e.eps

*

Wiring diagrams for CTL3, 4 jack is shown below. Make connections

after first checking the wiring diagrams of other equipment you

intend to connect.

fig.XLR/TRSJack.eps

922

*

This instrument is equipped with balanced type jack (XLR=SUB

OUT). Wiring diagrams for this jacks is shown below. Make

connections after first checking the wiring diagrams of other

equipment you intend to connect.

fig.XLR/TRSJack.eps

925

*

Use only the specified expression pedal (Roland EV-5, BOSS FS-

500L/500H with a connection cable (stereo 1/4” phone – stereo 1/4”

phone); sold separately). By connecting any other expression pedals,

you risk causing malfunction and/or damage to the unit.

927

*

Depending on the circumstances of a particular setup, you

may experience a discomforting sensation, or perceive that

the surface feels gritty to the touch when you touch this

device, microphones connected to it, or the metal portions of

other objects, such as basses. This is due to an infinitesimal

electrical charge, which is absolutely harmless. However, if

you are concerned about this, connect the ground terminal

(see figure) with an external ground. When the unit is

grounded, a slight hum may occur, depending on the

particulars of your installation. If you are unsure of the

connection method, contact the nearest Roland Service

Center, or an authorized Roland distributor, as listed on the

“Information” page.

Unsuitable places for connection

• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
• Telephone-line ground or lightning rod (may be

dangerous in the event of lightning)

926a

*

When connection cables with resistors are used, the volume level of

equipment connected to the BASS INPUT may be low. If this

happens, use connection cables that do not contain resistors.

*

Never connect anything other than the FC-300’s RRC2 OUT

connector to the VB-99’s RRC2 IN connector. Connecting to a LAN

or other devices that use modular jacks of the same size and shape

(RJ45) may result in damage to the VB-99 and/or the connected

device.

*

If using a commercially available ethernet cable as the RRC2

connecting cable, be sure that the cable meets the following

specifications:

• Category 5 (Cat5) or above
• Maximum length of 15 meters
• Cable designed for straight-through connections

*

Crossover cables cannot be used.

*

Do not subject the RRC2 cable to stress or physical shock.

*

Carefully connect the RRC2 cable all the way in–until it is firmly
connected to the RRC2 IN connector.

*

When outputting in mono, connect a cable only to the MAIN OUT

L/MONO jack.

*

You cannot use COSM BASS or POLY FX with signals input via

BASS IN. The GT-10B’s internal FX, COSM AMP, MIXER, and

Lock

Indicator

AC Outlet

Power Cord

AC Adaptor

Cord Hook

The cord of
the supplied AC Adaptor

To the Power Outlet

=CTL3

=CTL4

VB-99_e.book 18 ページ 2008年8月18日 月曜日 午後1時10分

Advertising
This manual is related to the following products: