Roland XP-30 - Manual (Page 104)

104
Chapter 3. Creating Your Own Sounds
ChoRate (Chorus Rate)
Adjust the modulation speed of the chorus effect.
Chorus Depth
Adjust the modulation depth of the chorus effect.
Chorus Balance #
Adjust the volume balance between the overdrive sound that
is sent through the chorus and the overdrive sound that is
not sent through the chorus. With a setting of “D100: 0W,”
only the overdrive sound will be output. With a setting of
“D0: 100W,” only the overdrive sound that is sent through
the chorus will be output.
Level (Output Level)
Adjust the output level.
27: OVERDRIVE → FLANGER
This effect connects an overdrive and a flanger in series.
fig.3-72
OD Drive
Adjust the degree of overdrive distortion. The volume will
change together with the degree of distortion.
OD Pan (Overdrive Pan) #
Adjust the stereo location of the overdrive sound. L64 is far
left, 0 is center, and 63R is far right.
Flg Dly (Flanger Pre Delay Time)
Adjust the time delay from when the direct sound begins
until the flanger sound is heard.
FlgRate (Flanger Rate)
Adjust the modulation speed of the flanger effect.
Flg Dpt (Flanger Depth)
Adjust the modulation depth of the flanger effect.
Flg Fbk (Flanger Feedback Level)
Adjust the proportion (%) of the flanger sound that is fed
back into the effect. Negative (-) settings will invert the phase.
Flanger Balance #
Adjust the volume balance between the overdrive sound that
is sent through the flanger and the overdrive sound that is
not sent through the flanger. With a setting of “D100: 0W,”
only the overdrive sound will be output. With a setting of
“D0: 100W,” only the overdrive sound that is sent through
the flanger will be output.
Level (Output Level)
Adjust the output level.
28: OVERDRIVE → DELAY
This effect connects an overdrive and a delay in series.
fig.3-73
OD Drive
Adjust the degree of overdrive distortion. The volume will
change together with the degree of distortion.
OD Pan (Overdrive Pan) #
Adjust the stereo location of the overdrive sound. L64 is far
left, 0 is center, and 63R is far right.
DlyTime (Delay Time)
Adjust the time delay from when the direct sound begins
until the delay sound is heard.
Dly Fbk (Delay Feedback Level)
Adjust the proportion (%) of the delay sound that is fed back
into the effect. Negative (-) settings will invert the phase.
Delay HF Damp
Adjust the frequency above which delayed sound fed back to
the effect will be cut. If you do not want to cut the high
frequencies of the feedback, set this parameter to BYPASS.
Delay Balance (Delay Balance) #
Adjust the volume balance between the overdrive sound that
is sent through the delay and the overdrive sound that is not
sent through the delay. With a setting of “D100: 0W,” only
the overdrive sound will be output. With a setting of “D0:
100W,” only the overdrive sound that is sent through the
delay will be output.
Level (Output Level)
Adjust the output level.
29: DISTORTION → CHORUS
This effect connects distortion and chorus in series. The
parameters are essentially the same as “26:
OVERDRIVE
→ CHORUS,” with the exception of the
following two.
OD Drive
→ Dist Drive (Specify the amount of distortion.)
OD Pan → Dist Pan (Specify the stereo location of the
distortion sound.)
fig.3-74
L in
R in
Flanger Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Delay Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Chorus Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D