Yamaha RX-Z11 - Manual (Page 126)

Remote control features
126
En
You can program remote control codes from other remote controls.
Use the learning feature if you want to program functions not
included in the basic operations covered by the remote control
codes, or an appropriate remote control code is not available. You
can program the function of other remote control to the buttons in
the highlighted areas in the following illustration. The buttons can
be programmed independently for each control area.
• The remote control transmits infrared rays. If the other remote control also
uses infrared rays, this remote control can learn most of its functions.
However, you may not be able to program some special signals or
extremely long transmissions. Refer to the operating instructions for the
other remote control.
• You cannot program the desired remote control code even if you select the
buttons in the highlighted area in the above illustration depending on the
selected control area and the assigned library.
1
Set the operation mode selector to F
SOURCE and
then press an input selector button (3) to select the
desired control area.
The name of the control area you want to customize appears in
the display window (4) on the remote control.
y
• You can also select the desired control area by pressing 5SELECT
l / h repeatedly.
• If you want to select “TV”, set the operation mode selector to FTV.
Make sure that the operation mode selector is set to FSOURCE or
FTV. When you set the operation mode selector to FAMP and
program a remote control codes from other remote controls, the
programmed key cannot operate the amplifier function of this unit.
2
Press G
SETUP using a ballpoint pen or similar
object.
“SETUP” appears in the display window (4).
3
Press 9k / n repeatedly to select “LEARN” and then
press 9
ENTER.
The remote control enters the learning mode. “LEARN” and
the name of the selected control area appears in the display
window (4) alternately.
4
Place this remote control about 5 to 10 cm (2 to 4 in)
apart from the other remote control on a flat surface
so that their infrared transmitters are aimed at each
other and then press 9
ENTER.
“L–KEY” appears in the display window (4).
5
Press the button for which you want to program the
new function.
“START” appears in the display window (4).
Programming codes from other remote
controls (LEARN)
Notes
Note
AMP
TV
SOURCE
ZONE MODE
SELECT SETUP ID MACRO
4 3
SYSTEM MEMORY
VOLUME
DVD CD
V-AUX MULTI
AV TV
PHONO
CD-R
POWER STANDBY POWER POWER
DTV DVR VCR
DOCK TUNER XM
BD
HD DVD
MD
TAPE
CBL SAT
NET
USB
REC
SRCH MODE LEVEL
BAND
MENU TITLE
CLASSICAL 1 CLASSICAL 2 LIVE/CLUB ENTERTAIN
MEMORY
PC/MCX
RETURN DISPLAY
PRESET/CH
ENTER CAT. A-E
MUTE
2 1
NET RADIO
PRG SELECT
USB
MOVIE STEREO SUR. DECODE
EXTD SUR.
ENHANCER
THX STRAIGHT PURE DIRECT
PARTY SLEEP HDMI OUT AUDIO SEL
TV VOL TV CH TV 3D DSP
1 2 3 4
5 6 7 8
ENT.
MUTE AUDIO
INPUT
9 0 10
Set to
SOURCE
(U.S.A. and Canada models)
DVD
SETUP
START DVD
AMP TV
SOURCE
ZONE
MODE
SELECT
SETUP
ID
MA
CR
O
4
3
SYSTEM MEMOR
Y
V OLUME
DV
D
C D
V-
A U X
MUL
TI
AV
TV
PHONO
CD-R PO
WER
ST ANDBY
PO
WER
PO
WER
DTV
D VR
VCR
DOCK
TUNER
XM
BD HD D
V D
MD TA
P
E
CBL SA
T
NET USB SRCH MODE
LEVEL BAND
MENU
TITLE MEMOR
Y
RETURN
DISPLA
Y
PRESET/CH ENTER
CA T. A-E
MUTE
2
1
5 to 10 cm (2 to 4 in)
Other remote control
L-KEY
(U.S.A. and Canada
models)
AMP TV
SOURCE
ZONE
MODE
SELECT
SETUP
ID
MA
CR
O
4
3
SYSTEM MEMOR
Y
V OLUME
DV
D
C D
V- A U X
MUL
TI
AV
TV
PHONO
CD-R PO
WER
ST ANDBY
PO
WER
PO
WER
DTV
D VR
VCR
DOCK
TUNER
XM
BD HD D
V D
MD TA
P
E
CBL SA
T
NET USB SRCH MODE
LEVEL BAND
MENU
TITLE MEMOR
Y
RETURN
DISPLA
Y
PRESET/CH ENTER
CA T. A-E
2
1
START
(U.S.A. and Canada
models)