Zenith DTV1080 - Manual (Page 2)

1
206-3675
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV/SATELLITE DISH INSTALLER:
This reminder is provided to call the cable TV system/satellite dish installer’s attention to Article 820-40 of the National Electric Code (U.S.A).
The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding sys-
tem of the building, as close to the point of the cable entry as practical.
POWER CORD POLARIZATION
Caution:
TO PREVENT ELECTRONIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Attention:
Pour eviter les chocs electriques, introduire la lame la plus large de la flche dans la born.
REGULATORY INFORMATION
This equipment, trade name Zenith, model number, DTV1080, has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
REGULATORY INFORMATION: FCC Part 68
• This product complies with Part 68 of the FCC rules. On the back of this product is a label that contains, among other information, the FCC regis-
tration number and Ringer Equivalent Number (REN) for this product. If requested, this information must be provided to the telephone company.
• The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result
in the devices not ringing in response to an incoming call. Typically, the sum of the RENs should not exceed five (5). To ve certain of the number of
devices that may be connected to the line (as determined by the total RENs) contact the local telephone company.
• If this product causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised
of your right to file a complaint with the FCC if you believe it is necessary.
• The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the product. If
this happens, the telephone company will provide advance notice so you can make the necessary modifications to maintain uninterrupted service.
• Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission, or corporate com-
mission for information.)
• If trouble is experienced with this product, for repair or warranty information, please contact Zenith Electronics Corporation. If the product is caus-
ing harm to the telephone network, the telephone company may request that you disconnect the product until the problem is resolved.
• An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone
network or premises wiring using a compatible modular jack which is Part 68 compliant. See installation instructions for details.
COMPLIANCE: The responsible party for this product’s compliance is:
Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL, 60069, USA
• Phone: 1-847-391-7000
CAUTION
DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY WITHOUT WRITTEN AUTHORIZATION FROM ZENITH ELECTRONICS CORPORATION.
UNAUTHORIZED MODIFICATION COULD VOID THE USER’S AUTHORITY TO OPERATE THIS PRODUCT.
THIS EQUIPMENT IS INTENDED TO RECEIVE AND DECODE SIGNALS TRANSMITTED ACCORDING TO ATSC DIGITAL TELEVISION STANDARD A/53,
DIRECTV

SPECIFICATION AND IS INTENDED TO BE USED WITH AN APPROPRIATE ANTENNA, DISH AND DISPLAY DEVICE THAT YOU MUST PROVIDE.
Dolby Digital ®
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works.
© 1992-1997 Dolby Laboratories, Inc. All rights reserved.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRES-
ENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTI-
TUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERAT-
ING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
WARNING:
TO REDUCE THE RISK OF ELECTRONIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.