Garmin G950 Tecnam 2006T - Manual (Page 34)

Garmin G950 Pilot’s Guide for the Tecnam P2006T 190-01146-00 Rev. A 22
SYSTEM OVERVIEW
SY
STEM
O
VER
VIEW
FLIGHT
INSTRUMENTS
EIS
AUDIO P
ANEL
& CNS
FLIGHT
MANA
GEMENT
HAZARD
AV
OID
ANCE
AFCS
ADDITIONAL FEA
TURES
APPENDICES
INDEX
OBS Selects OBS mode on the CDI when navigating by GPS (only available with active
leg)
CDI Cycles through GPS, VOR1, and VOR2 navigation modes on the CDI
DME Displays the DME Tuning Window, allowing tuning and selection of the DME
(optional)
XPDR Displays transponder mode selection softkeys
STBY Selects standby mode (transponder does not reply to any interrogations)
ON Selects Mode A (transponder replies to interrogations)
ALT Selects Mode C – altitude reporting mode (transponder replies to identification and
altitude interrogations)
GND Manually selects Ground Mode, the transponder does not allow Mode A and
Mode C replies, but it does permit acquisition squitter and replies to discretely
addressed Mode S interrogations
VFR Automatically enters the VFR code (1200 in the U.S.A. only)
CODE Displays transponder code selection softkeys 0-7
0 — 7 Use numbers to enter code
BKSP Removes numbers entered, one at a time
IDENT Activates the Special Position Identification (SPI) pulse for 18 seconds, identifying
the transponder return on the ATC screen
TMR/REF Displays Timer/References Window
NRST Displays Nearest Airports Window
ALERTS Displays Alerts Window
Figure 1-19 Top Level PFD Softkeys
INSET XPDR IDENT TMR/REF NRST ALERTS OBS PFD CDI
Press the CDI Softkey to cycle through
navigation sources:
- GPS
- NAV1 (VOR/LOC)
- NAV2 (VOR/LOC)
Press the BACK Softkey to return
to the top-level softkeys.
Press the BACK Softkey to return
to the top-level softkeys.
XPDR
STBY ON ALT VFR IDENT BACK ALERTS CODE
IDENT BACK ALERTS 0 1 2 3 4 5 6 7 BKSP
BACK
Press the BACK Softkey to return
to the top-level softkeys.
DCLTR
DCLTR-2
DCLTR-3
DCLTR-1
TOPO ALERTS TERRAIN OFF
INSET
STD BARO BACK ALERTS WIND HSI FMT
PFD
BRG1 BRG2
Press the BACK Softkey to return
to the top-level softkeys.
ALT UNIT DFLTS
Press the BRG1/BRG2
softkeys to display/remove
the Bearing Information
windows and cycle through
bearing sources:
- NAV1/NAV2
- GPS
GND
DME
(optional)
HPA BACK ALERTS METERS IN
BACK ALERTS OPTN1 OPTN2 OPTN3 OFF
BACK ALERTS 360 HSI ARC HSI
TRFC-1
TRFC-2
Figure 1-20 INSET Softkeys
INSET XPDR IDENT TMR/REF NRST ALERTS OBS PFD CDI
Press the CDI Softkey to cycle through
navigation sources:
- GPS
- NAV1 (VOR/LOC)
- NAV2 (VOR/LOC)
Press the BACK Softkey to return
to the top-level softkeys.
Press the BACK Softkey to return
to the top-level softkeys.
XPDR
STBY ON ALT VFR IDENT BACK ALERTS CODE
IDENT BACK ALERTS 0 1 2 3 4 5 6 7 BKSP
BACK
Press the BACK Softkey to return
to the top-level softkeys.
DCLTR
DCLTR-2
DCLTR-3
DCLTR-1
TOPO ALERTS TERRAIN OFF
INSET
STD BARO BACK ALERTS WIND HSI FMT
PFD
BRG1 BRG2
Press the BACK Softkey to return
to the top-level softkeys.
ALT UNIT DFLTS
Press the BRG1/BRG2
softkeys to display/remove
the Bearing Information
windows and cycle through
bearing sources:
- NAV1/NAV2
- GPS
GND
DME
(optional)
HPA BACK ALERTS METERS IN
BACK ALERTS OPTN1 OPTN2 OPTN3 OFF
BACK ALERTS 360 HSI ARC HSI
TRFC-1
TRFC-2