Spicer Driveline Components Catalog - End Yokes - Manual (Page 13)

J300P-4
END YOKES with SPLINED HOLES
R Q S End Yoke Assy. Slinger/Plug Spicer
Major Ground Length Centerline C'Bore Style (includes slinger/plug) Part Part
Diameter Hub Dia. Thru Hole to End Depth Order When Listed Number Number
11
Important: See Safety Information in General Information Section (J300P-GI)
• Part is discontinued  Part is available until supply is exhausted © Not sold separately
SPL170 SERIES (Continued) E-6.456 IN. D-2.166 IN. USE KIT SPL170-3X
USE BEARING RETAINER KIT NO. 170-70-18X
2.922-22 Involute Spline
2.922 3.747 2.645 5.930 .400 HR — — 170-4-1731-1
Counterbore at hub end.
SPL250 SERIES E-6.412 IN. D-2.362 IN. USE KIT SPL250X
USE BEARING RETAINED NO. 250-70-18X
2.024-39 Involute Spline
2.024 3.000 2.245 5.240 .280 HR 250-4-391-1X 232199 250-4-381-1•
2.114-32 Involute Spline
2.114 3.000 2.245 5.240 .424 HR 250-4-421-1X 232200 250-4-411-1©
2.143-41 Involute Spline
2.143 2.938 2.500 5.490 — HR 250-4-141-1X 232604 250-4-131-1©
2.225-6 Spline
2.225 3.000 3.250 6.240 — HR 250-4-541-1X 829-W 250-4-531-1©
2.225 3.000 3.250 6.250 — HR — — 250-4-811-1
2.274-44 Involute Spline
2.274 2.938 2.350 5.328 — HR 250-4-41-1X 232604 250-4-31-1©
2.274 2.938 2.500 5.484 — HR 250-4-61-1X 232168 250-4-51-1©
2.274 3.000 2.500 5.490 .236 HR 250-4-81-1X 232511 250-4-71-1•
2.364-36 Involute Spline
2.364 3.000 2.685 5.680 — HR 250-4-371-1X• 232199 250-4-361-1
2.374-46 Spline
2.374 3.250 2.625 5.610 — HR 250-4-781-1X• 231179 250-4-771-1©
2.374 3.250 2.875 5.870 .140 HR 250-4-291-1X 231179 250-4-281-1©
2.374 3.250 2.875 5.870 .140 HR 250-4-301-1X 231615 250-4-281-1©
2.374 3.500 2.406 6.140 — HR 250-4-651-1X 232042-10 250-4-641-1
2.374 3.750 2.400 6.650 — HR 250-4-801-1X — 250-4-791-1©
2.374 3.750 2.406 5.410 — HR 250-4-621-1X — 250-4-601-1©
Assy includes electronic speedometer gear #231528
2.390-46 Involute Spline
2.390 3.250 2.312 5.312 .140 HR 250-4-03560-1X 5003552 250-4-341-1•
2.390 3.250 2.312 5.312 .140 HR 250-4-351-1X 231803 250-4-341-1•
2.390 3.250 2.312 5.312 .140 HR 5003560 5003552 250-4-341-1•
5003560 was replaced by 250-4-03560-1X
2.390 3.344 2.750 5.750 — HR — — 250-4-21-1
Coupling shaft yoke
2.390 3.375 3.195 6.760 .580 HR 250-4-101-1X 232610 250-4-91-1
2.390 3.500 3.375 6.560 — HR — — 250-4-471-1•
2.500-10 Spline
2.500 3.500 2.406 5.500 — HR 250-4-711-1X 232042-11 250-4-701-1
2.500 3.750 3.000 6.062 — HR 250-4-201-1X 231616 250-4-191-1•
Hub machined for speedometer gear
2.500 3.750 3.000 6.250 — HR — — 250-4-561-1
Hub machined for speedometer gear
2.544-49 Involute Spline
2.544 3.750 3.000 6.250 — HR 250-4-161-1X 231616 250-4-151-1©
Hub machined for speedometer gear
2.544 3.819 2.125 5.830 .120 HR 5008459 5008437 250-4-1021-1©
5008459 was replaced by 250-4-08459-1X; 131435K = 5008459 yoke assy & nut# 131095; Spicer axles only
2.544 3.819 2.125 5.830 .120 HR 250-4-08459-1X 5008437 250-4-1021-1©
131435K = 5008459 yoke assy & nut# 131095; Spicer axles only
2.544 3.819 2.126 5.830 .120 HR 131435K 5008437 5008459
5008459 was replaced by 250-4-08459-1X; Attach nut #131095 on Spicer Axle only