Spicer Driveline Components Catalog - End Yokes - Manual (Page 60)

END YOKES with SPLINED HOLES
J300P-4
R Q S End Yoke Assy. Slinger/Plug Spicer
Major Ground Length Centerline C'Bore Style (includes slinger/plug) Part Part
Diameter Hub Dia. Thru Hole to End Depth Order When Listed Number Number
58
Important: See Safety Information in General Information Section (J300P-GI)
WB Style
• Part is discontinued  Part is available until supply is exhausted © Not sold separately
6C SERIES (Continued) P-5.530 T-1.688 KEYWAY: 0.561 USE KIT 050138000
1.650-16 Involute Spline
1.650 2.375 2.000 3.062 — WB — — 6C-4-91
Tapped holes in yoke ears
1.650 2.375 2.000 3.780 — WB — — 6C-4-181
Flanged yoke w/six, tapped holes in flange
1.793-34 Spline
1.793 2.625 2.188 3.250 — WB — — 128594HX
1.796-34 Involute Spline
1.796 2.625 2.098 3.515 .200 WB — — 6C-4-211M
Tapped holes in yoke ears
1.922-14 Involute Spline
1.922 2.375 2.183 3.500 — WB — — 6C-4-141
Tapped holes in yoke ears
1.922 2.375 2.183 3.750 — WB — — 6C-4-201
Flanged WB yoke w/tapped holes in yoke ears
1.922 2.375 2.184 3.495 .120 WB — — 6C-4-151
Flanged WB yoke w/tapped holes in yoke ears
1.922 2.375 2.184 3.495 .120 WB — — 6C-4-161M
Flanged WB yoke w/tapped holes in yoke ears
1.922 2.375 2.188 3.122 .120 WB — — 6C-4-81
Tapped holes in yoke ears
2.005-15 Involute Spline
2.005 2.875 2.500 3.880 .250 WB — — 6C-4-101
Tapped holes in yoke ears
2.005 2.875 2.500 3.880 .250 WB — — 6C-4-111
Tapped holes in yoke ears
2.289-17 Involute Spline
2.289 2.750 2.500 3.810 — WB — — 6C-4-251
Tapped holes in yoke ears
2.289 2.750 2.500 4.250 — WB — — 6C-4-261
Flanged yoke w/8 tapped holes in flange
2.541-19 Involute Spline
2.541 3.125 3.125 4.589 .250 WB — — 6C-4-41
Tapped holes in yoke ears
7C SERIES P-5.842 T-1.938 KEYWAY: 0.624 USE KIT 5-7105X
1.605-15 Involute Spline
1.605 2.125 1.938 3.620 — WB — — 7C-4-81
Tapped holes in yoke ears
1.650-16 Involute Spline
1.650 2.375 2.000 3.250 .380 WB — — 7C-4-261
Tapped holes in yoke ears
1.650 2.375 2.000 3.780 — WB — — 7C-4-211
Flanged yoke w/6 drilled holes in flange