Spicer Driveline Components Catalog - End Yokes - Manual (Page 53)

END YOKES with SPLINED HOLES
R Q S End Yoke Assy. Slinger/Plug Spicer
Major Ground Length Centerline C'Bore Style (includes slinger) Part Part
Diameter Hub Dia. Thru Hole to End Depth Order When Listed Number Number
51
Important: See Safety Information in General Information Section (J300P-GI)
• Part is discontinued  Part is available until supply is exhausted © Not sold separately
J300P-4
1760 SERIES (Continued) E-7.000 (7.094 FOR HR STYLE) D-1.938 USE KIT 5-407X, 5-677X
FOR HR STYLE USE STRAP KIT 6.5-70-18X
2.544-49 Involute Spline (Continued)
2.544 3.819 2.677 6.050 .240 HR 131520K 5008437 5008441
5008441 was replaced by 6.3-4-08441-1X; Attach nut #131095 on Spicer Axle only
2.544 4.000 2.750 5.562 .180 BP — — 6.3-4-1251•
2.544 4.000 2.750 5.562 .180 HR — — 6.3-4-1251-1
2.635-20 Involute Spline
2.635 3.750 2.750 5.562 — BP 6.3-4-871X• 231745 6.3-4-41•
Hub machined for speedometer gear; Hub Dia. 3.000 if used on Spicer 1241 Aux. Trans.
2.635 3.750 2.750 5.562 — HR 6.3-4-871-1X 231745 6.3-4-41-1§
Hub machined for speedometer gear; Hub Dia. 3.000 if used on Spicer 1241 Aux. Trans.
2.750-10 Spline
2.750 — 3.000 5.969 — HR — — 6.3-4-1201-1
Hub diameter not ground
2.750 3.750 3.000 5.969 — BP 6.3-4-721X 230902 6.3-4-661©
2.750 3.750 3.000 5.969 — HR 6.3-4-721-1X 230902 6.3-4-661-1§
2.750 3.750 3.000 5.969 — BP 6.3-4-791X 231616 6.3-4-711
2.750 3.750 3.000 5.969 — HR 6.3-4-791-1X 231616 6.3-4-711-1
2.750 4.000 2.938 6.000 — BP — — 6.3-4-61§
Hub machined for speedometer gear
2.750 4.000 2.938 6.000 — HR — — 6.3-4-61-1•
Hub machined for speedometer gear
2.794-54 Involute Spline
2.794 — 2.750 5.625 — BP — — 6.3-4-1681
Hub diameter not ground
2.794 — 2.750 5.625 — HR — — 6.3-4-1681-1
Hub diameter not ground
2.794 3.750 3.000 5.970 — HR — — 6.3-4-1051-1•
2.795-55 Involute Spline
2.795 4.719 2.047 5.000 .150 HR — — 6.3-4-1581-1•
OEM only
2.795 4.725 2.047 5.000 .150 HR 6.3-4-1831-1X© 233062 6.3-4-1761-1•
OEM only
2.795 4.725 2.047 5.000 .150 HR 6.3-4-1821-1X© 233061 6.3-4-1761-1•
OEM only
2.795 4.725 2.047 5.000 .150 HR 6.3-4-1771-1X• 233040 6.3-4-1761-1•
OEM only
2.798-21 Involute Spline
2.798 3.531 2.078 4.844 .080 HR — — 6.3-4-1191-1•
1800 SERIES E-6.594 D-2.312 USE KIT 5-124X
2.002-15 Involute Spline
2.002 3.250 2.703 4.938 .687 BP — — 6.5-4-2961
1810 SERIES E-7.547 (7.643 FOR HR STYLE) D-1.938 USE KIT 5-281X, 5-676X
FOR HR STYLE USE STRAP KIT 6.5-70-18X
1.939-30 Involute Spline
1.939 3.000 2.250 5.375 — BP — — 6.5-4-2051
1.964-10 Spline
1.964 2.625 2.250 5.625 .250 BP 6.5-4-2351X§ 230998 6.5-4-2001
Chamfered Counterbore
2.000-10 Spline
2.000 2.938 2.562 5.375 — BP 6.5-4-2341X 98-1361 6.5-4-1921•