Extron Electronics CrossPoint 300 Series - Manual (Page 81)

4-11 CrossPoint 300 Matrix Switchers • Programmer’s Guide
Command/response table for SIS commands (Cont’d)
Command ASCII Command Response Additional description
(host to switcher) (switcher to host)
View ties, gain, mutes, and presets
View RGBHV output tie X3 & X2
Example: 15& 27 Input 27 RGBHV tied to output
15.
View video output tie X3 % X2
Example: 7% 02 Input 2 video tied to output 7.
View audio output tie X3 $ X2
Example: 3$ 06 Input 6 audio tied to output 3.
View input gain X2 G X5
Example: 4G -02 Gain for input #4 is -2 dB.
View output mutes Esc VM X10
1
X10
2 ... X10
n Each X10 response is the mute
status of an output, starting from
output 1, n is the maximum
number of outputs for this
model.
Example (CrossPoint 300 816 HVA): Esc VM 0 0 0 0 1 0 0 0 0 0 0 2 3 0 0 0 Output 5 video is muted, output
12 audio is muted, and output 13
video and audio are muted. All
other outputs are unmuted.
Example (CrossPoint 300 84 HVA): Esc VM 0 0 0 0 All outputs are unmuted.
View video global preset configuration Esc X9 *1*1VC X2
1 • X2
2 • X2
3 •...• X2
16 •Vid Show preset X9 ’s video
configuration. Show the video
input tied to 16 sequential
outputs, starting from output 1.
Command description: Esc preset#*output (O)# 1*1(=video)VC
Response description: input # (I#) assigned to O#1•I# assigned to O#2...I# assigned to O#16•Vid
Example (CrossPoint 300 1616): Esc 4*1*1VC
1 Output:
Response = tied input:
input 14 tied to output 3
2 3 4 5 6 7 8 9 10 11 12
08•08•14•08•08•09•09•00•08•01•01•01•08•08•08•08•Vid
13 14 15 16
no tied input input 8 tied to output 13
Esc X9
*1*1VC where
X9
= 0 returns the switcher’s current video configuration.
Each position shown in the response is an output: left = output 1, right= output 16. The number in each position is the
input tied to that output.
Video — Input 1 is tied to outputs 10 through 12; input 8 to outputs 1, 2, 4, 5, 9, and 13 through 16; input 14 to output 3;
and input 9 to outputs 6 and 7. No input is tied to output 8.
View audio global preset configuration Esc X9 *1*2VC X2
1 • X2
2 • X2
3 •...• X2
16 •Aud Show preset X9 ’s audio
configuration. Show the audio
input tied to 16 sequential
outputs, starting from output 1.
Command description: Esc preset#*output# 1*2(=audio)VC
Response description: input # (I#) assigned to O#1•I# assigned to O#2...I# assigned to O#16•Aud
Example (CrossPoint 128 HVA): Esc 0*1*2VC {see below} Preset 0 is the current
configuration.
01 Output:
Response = tied input:
input 1 tied to output 3
02 03 04 05 06 07 08
01•01•01•01•02•12•12•00•--•--•--•--•--•--•--•--•Aud
13 14 15 16 09 10 11 12
no tied input no outputs
Esc X9 *1*2VC where X9 = 0 returns the switcher’s current audio configuration.
Audio — Input 1 is tied to outputs 1 through 4, input 2 is tied to output 5, and input 12 is tied to outputs 6 and 7. No
input is tied to output 8. The switcher in this example is a CrossPoint 300 128 HVA, so outputs 9 through 16 are not
present.