LiftMaster LA500 Residential / Light Commercial Swing Gate Operator - Manual (Page 39)

37
GATE OPERATOR SETUP EXAMPLES
ADDITIONAL FEATURES
GATE OPERATOR SETUP EXAMPLES
The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including
all necessary secondary entrapment protection systems.
RESIDENTIAL SMALL
: One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns
RESIDENTIAL LARGE: A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access trumps security concerns
COMMERCIAL: Business site where security (gate closed) is important
INDUSTRIAL: Large business site where security is required
Setting RESIDENTIAL SMALL RESIDENTIAL LARGE COMMERCIAL INDUSTRIAL
Quick Close switch setting Normally set to OFF. Normal gate
close (timer or control).
Normally set to OFF. Normal gate
close (timer or control).
Normally set to OFF. Normal gate
close (timer or control).
Set to ON, so that gate closes
immediately after vehicle passes
interrupt loop.
AC Fail Open switch setting Normally set to BATT. Run on
battery if AC power fails.
Normally set to BATT. For local
jurisdiction requirement, set to
OPEN so that the gate will open
approximately 15 seconds after AC
power fail.
Normally set to BATT. Run on
battery if AC power fails.
Normally set to BATT. Run on
battery if AC power fails.
Low Battery switch setting Normally set to OPEN. If powered
from battery and battery is low,
gate stays open.
Normally set to OPEN. If powered
from battery and battery is low,
gate stays open.
Normally set to CLOSE. If powered
from battery and battery is low,
gate stays close.
Normally set to CLOSE. If powered
from battery and battery is low,
gate stays close.
Anti-Tail switch setting Normally set to OFF. Interrupt loop
reverses a closing gate.
Normally set to OFF. Interrupt loop
reverses a closing gate.
Set to ON. In attempt to prevent
vehicle tail-gating, interrupt loop
pauses a closing gate.
Set to ON. In attempt to prevent
vehicle tail-gating, interrupt loop
pauses a closing gate.
Bipart Delay switch setting For DUAL-GATE site, set to ON for
gate that delays upon opening
For DUAL-GATE site, set to ON for
gate that delays upon opening
For DUAL-GATE site, set to ON for
gate that delays upon opening
For DUAL-GATE site, set to ON for
gate that delays upon opening
Aux Relay Out – Open
Limit Switch
Typically not required. Use with SAMS (Sequence Access
Management System)
1) Use with SAMS (Sequence Access
Management System)
2) Connect “Gate Open” indicator
(e.g. light)
1) Use with SAMS (Sequence Access
Management System)
2) Connect “Gate Open” indicator
(e.g. light)
Aux Relay Out – Close
Limit Switch
Typically not required. Typically not required. Connect “Gate Close/Secure”
indicator (e.g. light)
Connect “Gate Close/Secure”
indicator (e.g. light)
Aux Relay Out – Gate
Motion
Attach alert signal (audible or
visual alert system)
Attach alert signal (audible or
visual alert system)
Attach alert signal (audible or
visual alert system)
Attach alert signal (audible or
visual alert system)
Aux Relay Out – Pre-
Motion Delay
Attach alert signal (audible or
visual alert system)
Attach alert signal (audible or
visual alert system)
Attach alert signal (audible or
visual alert system)
Attach alert signal (audible or
visual alert system)
Aux Relay Out – Power Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries)
Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries)
Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries)
Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries)
Aux Relay Out – Tamper Attach alert signal (audible or
visual alert system) to indicate if
gate is manually tampered with by
being pushed off of close limit
Attach alert signal (audible or
visual alert system) to indicate if
gate is manually tampered with by
being pushed off of close limit
Attach alert signal (audible or
visual alert system) to indicate if
gate is manually tampered with by
being pushed off of close limit
Attach alert signal (audible or
visual alert system) to indicate if
gate is manually tampered with by
being pushed off of close limit
Cycle Quantity Feedback Use during servicing only to
determine operator cycles
Use during servicing only to
determine operator cycles
Use during servicing only to
determine operator cycles
Use during servicing only to
determine operator cycles
Fire Dept Open input Typically not required. Connect emergency access system
(Knox box switch, SOS system, etc.)
Typically not required. Typically not required.