System Sensor PDRP-1002 - Manual (Page 2)

2 The PDRP-1002 PN 51135:A 03/11/99
Installation Precautions
– Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be connected to the
fire alarm control panel. Disconnect all sources of power before
servicing. Control unit and associated equipment may be damaged by
removing and/or inserting cards, modules, or interconnecting cables
while the unit is energized. Do not attempt to install, service, or operate
this unit until this manual is read and understood.
CAUTION - System Reacceptance Test after Software Changes: To
ensure proper system operation, this product must be tested in
accordance with NFPA 72-1993 Chapter 7 after any programming
operation or change in site-specific software. Reacceptance testing is
required after any change, addition or deletion of system components, or
after any modification, repair or adjustment to system hardware or
wiring.
All components, circuits, system operations or software functions known
to be affected by a change must be 100% tested. In addition, to ensure
that other operations are not inadvertently affected, at least 10% of
initiating devices that are not directly affected by the change, up to a
maximum of 50 devices must also be tested and proper system
operation verified.
This system meets NFPA requirements for operation at 0-49 O C/
32-120 O F and at a relative humidity of 85% RH (non-condensing) at
30 O C/86 O F. However, the useful life of the system's standby batteries
and the electronic components may be adversely affected by extreme
temperature ranges and humidity. Therefore, it is recommended that this
system and its peripherals be installed in an environment with a nominal
room temperature of 15-27
O C/60-80 O F.
Verify that wire sizes are adequate for all initiating device loops. Most
devices cannot tolerate more than a 10% I.R. drop from the specified
device voltage.
Like all solid state electronic devices, this system may operate
erratically or can be damaged when subjected to lightning induced
transients. Although no system is completely immune from lightning
transients and interferences, proper grounding will reduce
susceptibility. Overhead or outside aerial wiring is not recommended
due to an increased susceptibility to nearby lightning strikes. Consu
with the Technical Services Department if any problems are
anticipated or encountered.
Disconnect AC power and batteries prior to removing or inserting
circuit boards. Failure to do so can damage circuits.
Remove all electronic assemblies prior to any drilling, filing, reamin
or punching of the enclosure. When possible, make all cable entries
from the sides or rear. Before making modifications, verify that they
will not interfere with battery, transformer and printed circuit board
location.
Do not tighten screw terminals more than 9 in-lbs. Over tightenin
may damage threads, resulting in reduced terminal contact pressure
and difficulty with screw terminal removal.
This system contains static-sensitive components Always ground
yourself with a proper wrist strap before handling any circuits so that
static charges are removed from the body. Use static suppressive
packaging to protect electronic assemblies removed from the unit.
Follow the instructions in the installation, operating and
programming manuals. These instructions must be followed to avoid
damage to the control panel and associated equipment. FACP
operation and reliability depend upon proper installation.
Fire Alarm System Limitations
An automatic fire alarm system - typically made up of smoke
detectors, heat detectors, manual pull stations, audible warning devices
and a fire alarm control with remote notification capability can provide
early warning of a developing fire. Such a system, however, does not
assure protection against property damage or loss of life resulting from a
fire.
Any fire alarm system may fail for a variety of reasons:
Smoke detectors may not sense fire where smoke cannot reach the
detectors such as in chimneys, in walls, or roofs, or on the other side of
closed doors. Smoke detectors also may not sense a fire on another
level or floor of a building. A second floor detector, for example, may not
sense a first floor or basement fire. Furthermore, all types of smoke
detectors - both ionization and photoelectric types, have sensing
limitations. No type of smoke detector can sense every kind of fire
caused by carelessness and safety hazards like smoking in bed, violent
explosions, escaping gas, improper storage of flammable materials,
overloaded electrical circuits, children playing with matches, or arson.
IMPORTANT! Smoke detectors must be installed in the same room as
the control panel and in rooms used by the system for the connection of
alarm transmission wiring, communications, signaling and /or power. If
detectors are not so located, a developing fire may damage the alarm
system, crippling its ability to report a fire.
Audible warning devices such as bells may not alert people if thes
devices are located on the other side of closed or partly open doors o
are located on another floor of a building.
A fire alarm system will not operate without any electrical power. I
AC power fails, the system will operate from standby batteries only fo
a specified time.
Rate-of-Rise heat detectors may be subject to reduced sensitivity
over time. For this reason, the rate-of-rise feature of each detector
should be tested at least once per year by a qualified fire protection
specialist.
Equipment used in the system may not be technically compatible
with the control panel. It is essential to use only equipment listed fo
service with your control panel.
Telephone lines needed to transmit alarm signals from a premise to
central monitoring station may be out of service or temporarily
disabled.
The most common cause of fire alarm malfunctions, however, is
inadequate maintenance. All devices and system wiring should be
tested and maintained by professional fire alarm installers following
written procedures supplied with each device. System inspection an
testing should be scheduled monthly or as required by National and/o
local fire codes. Adequate written records of all inspections should b
kept.
FCC Warning
WARNING: This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instruction manual, may cause interference to radio communications, It
has been tested and found to comply with the limits for class A
computing device pursuant to Subpart B of 15 of FCC Rules, which is
designed to provide reasonable protection against such interference
when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference, in which
case the user will be required to correct the interference at his own
expense. Canadian Requirements
This digital apparatus does not exceed the Class A limits for radiatio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
Le present appareil numerique n'emet pas de bruits radioelectriques
depassant les limites applicables aux appareils numeriques de la
classe A prescrites dans le Reglement sur le brouillage
radioelectrique edicte par le ministere des Communications du
Canada.
While installing a fire alarm system may make lower insurance
rates possible, it is not a substitute for fire insurance!