ATTO Technology 2400C/R/D - Manual (Page 10)

5
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.2 ATTO FibreBridge 2390R/D Physical Attributes
The ATTO FibreBridge 2390R/D is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit
Fibre Channel connectivity to Ultra320 SCSI devices.
The FibreBridge 2390R/D is available in an industry-
standard IU form factor for easy integration into racks.
The advanced connectivity options make it suitable to
support next-generation storage media.
Dimensions
Width: 16.494 inches
Length: 10.000 inches
Height: 1.579 inches (1U)
Weight: approximately 8 pounds
Cooling and airflow
Operating temperature: 0-40 °C external
Humidity: 10-90% non-condensing
Air enters from the front and is exhausted out the
connector side. Ambient air near the inlets should not
exceed 40 °C. The unit automatically stops operation
if the temperature goes beyond this threshold.
CAUTION CAUTION
Do not block the enclosure’s vents. The
FibreBridge does not allow data transfer if
overheating occurs.
Power
The power supply circuit is permanently mounted
within the enclosure and is not hot swappable. It has
one standard IEC320 power receptacle and switch.
The universal power supply provides power for the
bridge board and cooling fan.
The power requirements of the ATTO FibreBridge
2390R plus the power draw of the other equipment in
the rack must not overload the supply circuit and/or
wiring of the rack.
Input voltage: 110/230V AC, with operating input
range of 90-132V AC or 175-264V AC, 100-240 VAC;
1.7-.7A, 50-60Hz.
Battery-backed event log SRAM & Real-Time-
Clock: a rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel interface
The optical SFP 4-Gb Fibre Channel port auto-
negotiates to 1-Gb, 2-Gb or 4-Gb devices.
SCSI ports
The two independent SCSI ports are Ultra320 SCSI
busses with VHDCI connector, downward compatible
with all forms of single-ended SCSI and all previous
SCSI protocols.
Management ports
The 10/100 Base T Ethernet port is accessible from
the RJ-45 connector to support local and remote
diagnostics, monitoring and management.
The RS-232 serial port provides
support for remote monitoring and
management using a DB9 connector.
The baud rate is programmable and
preset at the factory to 115200 bps.
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green Ready LED
blinks.
LED indicators
The LED indicators can be viewed from the connector
(back) side and the front side of the FibreBridge
2390R/D. (See Exhibit 1.2-1)
LEDs on the connector (back) side are:
1
9
8
7
6
5
4
3
2
RX
TX
GND