ATTO Technology 2400C/R/D - Manual (Page 46)

xiii
ATTO Technology Inc. FibreBridge Installation and Operation Manual
SNTPServer
Controls/displays the main IP address of the SNTP time server.
If the FibreBridge is unable to contact the specified SNTP time
server within 30 seconds, the FibreBridge tries to contact the
first auxiliary SNTP time server. If not successful, the
FibreBridge tries to contact the second auxiliary server. If not
successful, the FibreBridge continues to keep time based on the
most recent SNTP time server, physical RTC or manual
initialization or synchronization.
Default: 192.43.244.18
set SNTPServer xxx.xxx.xxx.xxx
Requires a SaveConfiguration Restart command
get SNTPServer
SpeedWrite
SpeedWrite is a method to improve the performance of
WRITE commands to SCSI tape devices attached to the
FibreBridge. You can specify the SCSI bus, target and LUN of a
mapped device or specify all to control the state of all currently
mapped SCSI devices.
Default: all disabled
set SpeedWrite SCSI [sb st sl | all] [enabled | disabled]
Requires a SaveConfiguration command
get SpeedWrite SCSI [sb st sl | all]
SpeedWriteDefault
Specifies the state of SpeedWrite for any SCSI devices
mapped manually or using an AutoMap command. If enabled,
any new SCSI device uses SpeedWrite automatically.
Default: disabled
set SpeedWriteDefault [enabled | disabled]
Requires a SaveConfiguration command
get SpeedWriteDefault
TailEventLog
Displays new events to the terminal. Type quit and press
Enter to exit.
TailEventLog
Temperature (FB 2390, FB 2400)
Displays the current internal temperature of the FibreBridge in
degrees Celsius.
get Temperature
Time
Controls/displays the time in a 24-hour format. The default time
is 00:00:00 and is accurate until the FibreBridge is reset or
power-cycled when it returns to the default.Time cannot be set
if
SNTP is enabled.
Default: 0:00:00
set Time [HH :MM :SS]
Requires a SaveConfiguration command
get Time
TimeZone
Controls/displays the time zone if SNTP is disabled. Setting
may be EST, CST, MST PST or a numerical offset from GMT
in the format +/- HH:MM. When
SNTP is enabled, applies the
time zone setting to the time retrieved from a specified SNTP
time server to determine local time.
Default: EST
set TimeZone [EST | CST | MST | PST | [+ / - HH : MM]]
Requires a SaveConfiguration command
get TimeZone
TraceLog
When enabled, records various system events to the trace log.
Default: disabled
set TraceLog [enabled | disabled]
get TraceLog
TraceLogFilter
Filters the display of data for specific FibreBridge ports when
TraceLog is enabled.
Default: all all all
set TraceLogFilter [FC | SCSI | all] [fp | sb | all] [none |
ChkCond | all]
get TraceLogFilter [FC | SCSI | all] [fp | sb | all ]
Username
Specifies user name for all Telnet, FTP and ExpressNAV user
management console sessions. Username is case
insensitive, 1-32 characters, no spaces.
Default: root
set Username
Requires a SaveConfiguration command
get Username
VerboseMode
Specifies the detail of feedback for the command line interface.
Disabling this option removes parameter names from action
commands and removes descriptions from information
commands.
Default: enabled (returns have parameter information)
set VerboseMode [enabled | disabled]
get VerboseMode
VirtualDriveResponse
Provides proxy responses to SCSI INQUIRY and TEST UNIT
READY commands if a SCSI device is in a timeout or busy. Host
systems may then assign devices consistently despite the
device’s state during execution of SCSI commands.
Default: disabled
set VirtualDriveResponse [enabled | disabled]
Requires a SaveConfiguration restart command
get VirtualDriveResponse