AMD Geode SC1201 - Manual (Page 361)

AMD Geode™ SC1200/SC1201 Processor Data Book 361
Video Processor Module - Video Processor Registers - Function 4 32579B
8 Video Data Capture Active. (Read Only)
0: Video data is not being stored to memory.
1: Video data is now being stored to memory.
7:1 Reserved. (Read Only)
0 Run Status. (Read Only)
0: Video port capture is not active.
1: Video port capture is in progress.
Offset 0Ch-0Fh Reserved Reset Value: 00h
Offset 10h-13h Video Current Line Register (RO) Reset Value: xxxxxxxxh
31:10 Reserved.
9:0 Current Line. Indicates the video line currently being stored to memory. The count indicated in this field is reset to 0 at the
start of each field.
Offset 14h-17h Video Line Target Register (R/W) Reset Value: 00000000h
31:10 Reserved. Must be set to 0.
9:0 Line Target. Indicates the video line to generate an interrupt on.
Offset 18h-1Bh Odd Field VBI Line Enable Register (R/W) Reset Value: 00000000h
31:24 Reserved.
23:0 VBI Odd Field Line Enable. In Direct VBI mode, each of bits [23:0] enables a received odd field VBI line to be passed
directly to the TVOUT block.
0: Disable the line.
1: Enable the line.
Offset 1Ch-1Fh Even Field VBI Line Enable Register (R/W) Reset Value: 00000000h
31:24 Reserved.
23:0 VBI Even Field Line Enable. In Direct VBI mode, each of bits [23:0] enables a received even field VBI line to be passed
directly to the TVOUT block.
0: Disable the line.
1: Enable the line.
Offset 20h-23h Video Data Odd Base Register (R/W) Reset Value: 00000000h
This register specifies the base address in graphics memory where odd video field data are stored. Changes to this register take effect
at the beginning of the next field. The value in this register is 16-byte aligned.
Note: This register is double-buffered. When a new value is written to this register, the new value is placed in a special "pending" reg-
ister, and the "Base Register Not Updated" bit (F4BAR2+MemoryOffset 08h[21]) is set to 1. The Video Data Odd Base register
(this register) is not updated at this point. When the first data of the next field is stored to memory, the pending values of all
base registers (including this one) are written to the appropriate base registers, and the "Base Register Not Updated" bit is
cleared.
31:0 Video Odd Base Address. Base address where odd video data are stored in graphics memory. Bits [3:0] are always 0, and
define the required address space.
Offset 24h-27h Video Data Even Base Register (R/W) Reset Value: 00000000h
This register specifies the base address in graphics memory where even video field data are stored. Changes to this register take effect
at the beginning of the next field. The value in this register is 16-byte aligned.
Note: This register is double-buffered. When a new value is written to this register, the new value is placed in a special "pending" reg-
ister, and the "Base Register Not Updated" bit (F4BAR2+MemoryOffset 08h[21]) is set to 1. The Video Data Even Base register
(this register) is not updated at this point. When the first data of the next field is stored to memory, the pending values of all
base registers (including this one) are written to the appropriate base registers, and the "Base Register Not Updated" bit is
cleared.
31:0 Video Even Base Address. Base address where even video data are stored in graphics memory. Bits [3:0] are always 0,
and define the required address space.
Table 7-10. F4BAR2+Memory Offset: VIP Configuration Registers (Continued)
Bit Description