Specifications, Additional information – Sony PCM-R500 User Manual
Page 32
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Additional Information
Specifications
Recording section
Tape
Digital audio tape
Recording head
Rotary head
Recording time
Standard: 120 minutes
Long-play: 240 minutes
(DT-120)
Tape speed
Standard: 8.15 mm/s
Long-play: 4.075 mm/s
Drum
rotation
Standard; 2,000 rpm
Long-play: 1,000 rpm
Error correction
Double-encoded Reed Solomon code
Tape section
Track pitch
13.6 pm (20.4 pm)
Sampling frequency
48 kHz, 44.1 kHz, 32 kHz
Modulation system
8-10 modulation
Transfer rate
2.46 Mbit/sec
Number of channels
2 channels, stereo
D / A conversion
Standard: 16-bit linear
(quantization)
Long-play: 12-bit non-linear
General section
Power requirements
Where purchased
Power requirements
U.S. A./Canada
120 V AC, 60 Hz
Europe/U.K
230 V AC, 50/60 Hz
Power consumption
- PCM-R500: 34W
PCM-R700: 34W
Dimensions
Approx 482 X 145 x 355 mm (w/h/d)
(19
x
5V4 xl4inches)
(not including rack mount adaptor)
Weight
PCM-R500: Approx 7.2kg (15 lb 14 oz)
PCM-R700: Approx 7.3kg (16 lb 2 oz)
Remote commander RM-D757 (supplied)
Remote control system
Infrared control
Power requirements
3V DC, with two size-AA (R6) batteries
Dimensions
Approx 45 X 210 X 26 mm (w/h/d)
(I’-Vif-X 8 V
h
X 1 Vib inches)
Weight
Approx lOOg (3.5 oz) inch batteries
Input connectors
Analog Input
Connector Type
Input impedance Rated input level*’
ANALOG Phono-
47kilohms -12 dBs
(UNBALANCE) plug jack
ANALOG XLR-3
10 kilohms +4 dBs
(BALANCE) (FEMALE) or more (factory setting)
(balanced)
Digital Input
Connector
Type
Input impedance Rated input level
AES/EBU
XLR-3
(FEMALE)
110 ohms
(balanced)
—
COAXIAL
Phono-plug
jack
0.5 Vp-p
Output connectors
Analog Output
Connector
Type
Output
impedance
Rated
output
level*’
Load
impedance
ANALOG Phono-plug 1 kilohm
(UNBALANCE) jack
-12 dBs
47 kilohms
ANALOG
(BALANCE)
XLR-3
(MALE)
100 ohms
(balanced)
+4 dBs
(factory
setting)
10 kilohms
or more
PHONES
Stereo phone- .,,
, . c 100 ohms
plug jack
0.36 mW 32 ohms
Digital Output
Connector
Type
Output
impedance
Rated
output
level
Load
impedance
AES/EBU
XLR-3
(MALE)
35 ohms
(balanced)
—
110 ohms
COAXIAL Phono-plug
jack
75 ohms
0.5 Vp-p
75 ohms
Variable range of analog (BALANCE) input/output reference level*'
+4 dBs to -12 dBs
Maximum analog (BALANCE) output level
+24 dBs
Remote switch connectors
Audio characteristics
Frequency response*'
SIgnal-to-noise ratio*’
Total harmonic distortion*’
Wow and flutter
DIN connector (8-pin, parallel)
Monaural minijack (serial)
Standard: 20-20,000 Hz (±0.5 dB)
Long-play: 20-14,500 Hz (±0.5 dB)
90 dB or more (20 kHz LPF, A-
Weight filter ON)
Standard: 0.05% or less
Long-play: 0.3% or less
(1 kHz, Reference level 20 kHz
LPF ON)
Below measurable limit (±0.001%
W.PEAK)
a) The reference level corresponds to -20 dB on the peak
level meters.
b) During analog input with the SBM function off
Supplied accessories
See page 4
Design and specifications are subject to change without
notice.
32
^