Futaba 12FG - Manual (Page 54)

54
<Functions of Linkage Menu>
S1 button
EDIT button
EDIT dial
ŏ3XVKWKHS1EXWWRQIRU
VHFRQGWRUHWXUQWRWKH
KRPHVFUHHQ
ŏ7XUQ WKH EDIT  GLDO WR
PRYHRQWKHVFUHHQ
ŏ6 H O H F W  W K H  I X Q F W L R Q
QDPH DQG UHWXUQ WR WKH
S U H F H G L Q J  V F U H H Q  E \
SXVKLQJWKHEDITEXWWRQ
Frequency setting
The T12FG transmitter uses a synthesizer
system. Its frequency can be changed within the
range of the frequency band of the module used.
The frequency of the R5114DPS receiver is set
from the transmitter. Use a receiver matched to the
frequency band of the transmitter.
Receiver ID code
W h e n t h e R 5 11 4 D P S r e c e i v e r ( P C M - G 3
receiver) is used, the ID code located on the back
of the receiver case must be entered.
*When two receivers are used with a large model, etc., enter
the 2nd receiver ID also.
Modulation mode selection
With the T12FG, 3 modulation modes (PCM-G3/
PCM1024/PPM (FM)) can be selected. Select the
modulation mode matched to the type of receiver
used.
FREQUENCY )UHTXHQF\VHWWLQJPRGXODWLRQPRGHVHWWLQJUHFHLYHU,'FRGHVHWWLQJ
Frequency switching method
For a description of the frequency switching and
ID setting methods, refer to the procedure given in
the Basic Operation section.
Modulation scheme (Modulation) change
 8VH WKH (',7 GLDO WR PRYH WKH FXUVRU WR WKH
02'8/$7,21 LWHP DQG SXVK WKH (',7
EXWWRQ
*The modulation selection screen appears.
 8VH WKH (',7 GLDO WR VHOHFW WKH PRGH DQG
SXVKWKH(',7EXWWRQ
7KHFRQ¿UPDWLRQPHVVDJH02'8/7<3(,6&+$1*('
SURE?" appears.
 :KHQ WKH (',7 EXWWRQ LV SUHVVHG DJDLQ WKH
PRGHLVFKDQJHG
*Transmission stops and a transmit or do not transmit in the
QHZPRGHFRQ¿UPDWLRQPHVVDJH75$160,7"DSSHDUV
PCM-G3 communication mode selection
Two types of PCM-G3 communication modes
can be selected. (Mode A and Mode B)
Mode A is conventional mode and displays the
maximum performance of the servo response to
stick operation (recommended.) Mode B is a mode
with enhanced communication quality. For the
interference characteristic, ModeB is better than
ModeA. In communication mode B, the servo
response to stick operation is approximately 20%
lower than that of mode A.
C h o o s e t h e m o d e m a t c h e d t o t h e u s a g e
environment.
&RPSDWLEOHUHFHLYHU
0RGH$ 5'36DQG5'36
0RGH% 5'36 7KH5'36LVQRW0RGH%
FRPSDWLEOH
7RVWDUWWUDQVPLVVLRQVHOHFW><(6@ZLWKWKH(',7
GLDODQGSXVKWKH(',7EXWWRQ7RQRWWUDQVPLW
VHOHFW>12@DQGSXVKWKH(',7EXWWRQ
*When the mode is changed from the PCM-G3 mode to
DQRWKHUPRGHDQGWKHQXPEHURIFKDQQHOVLVLQVXI¿FLHQWGXH
to the wing type used, the mode cannot be changed.
Receiver ID code input
*Input the 8-digit ID number indicated on the receiver case.
8VHWKH(',7GLDOWRVHOHFW>5(&(,9(5,'@DQG
SXVK WKH (',7 EXWWRQ 7KH UHFHLYHU ,' FRGH
VHWXSVFUHHQDSSHDUV
 8VH WKH (',7 GLDO WR VHOHFW WKH FDQGLGDWH
FKDUDFWHURIWKHÀUVWGLJLWDQGSXVKWKH(',7
EXWWRQ6HTXHQWLDOO\VHWWKHGLJLWQXPEHU
*If you make a mistake, select [BACK SPACE] with the
EDIT dial and erase the incorrect digit by pressing the EDIT
button.
ŏ 6HOHFW >)5(48(1&<@ DW WKH OLQNDJH
PHQXDQGFDOOWKHVHWXSVFUHHQVKRZQ
EHORZE\SXVKLQJWKH(',7EXWWRQ