Futaba 12FG - Manual (Page 65)

65
<Functions of Linkage Menu>
S1 button
EDIT button
EDIT dial
ŏ3XVKWKHS1EXWWRQIRU
VHFRQGWRUHWXUQWRWKH
KRPHVFUHHQ
ŏ7XUQ WKH EDIT  GLDO WR
PRYHRQWKHVFUHHQ
ŏ6 H O H F W  W K H  I X Q F W L R Q
QDPH DQG UHWXUQ WR WKH
S U H F H G L Q J  V F U H H Q  E \
SXVKLQJWKHEDITEXWWRQ
SWASH 6ZDVKRSHUDWLRQOLQNDJHFRUUHFWLRQIXQFWLRQ KHOLFRSWHURQO\H[FHSW
VZDVKW\SH+
Neutral Point
At your linkages, if the servo horn deviates from
a perpendicular position at neutral, the linkage
compensation functions in this menu may not
compensate effectively. To correct this use the
Neutral Point function. This will move the neutral
point of the servos to the actual perpendicular
position. However, this adjustment changes only
the axis point of the compensation functions in this
menu, and does not affect the neutral position of
other functions.
Swash AFR
Swash AFR function reduces/increases/reverses
the rate (travel) of the aileron, elevator and
collective pitch functions, by adjusting or reversing
the motion of all servos involved in that function,
only when using that function.
Mixing Rate
This compensation mixing is used to correct
the tendency of the swash-plate for each control.
*Before making the following settings, use the EDIT dial to
move the cursor to the item you want to set.
Neutral point setting procedure
The neutral point becomes the correction
standard point.
*Adjusting the servo horn so that the neutral point is near the
50% position makes the mixing amount small.
1HXWUDOSRLQWVHWWLQJ
 0RYHWKHFXUVRUWRWKH>32,17@LWHPDQGKROG
WKHSLWFKRSHUDWLRQVRWKDWWKHVHUYRKRUQLV
DWDULJKWDQJOHWRWKHOLQNDJHURGDQGSXVK
WKH (',7 EXWWRQ IRU  VHFRQG DQG UHDG WKH
QHXWUDOSRVLWLRQ
*The neutral point can also be displayed by bar graph.
 $IWHU UHDGLQJ WKH QHXWUDO SRLQW XVH WKH
RWKHU FRUUHFWLRQ IXQFWLRQV WR PDNH IXUWKHU
DGMXVWPHQWV
The following compensation mixing is possible;
PIT to AIL, PIT to ELE, AIL to PIT, ELE to AIL,
and ELE to PIT (HR3 mode.) It adjusts the swash-
plate to operate correctly for each control using the
corresponding compensation mixing.
Linkage Compensation
This compensation mixing is used to correct the
tendency of the swash-plate for pitch control at low
pitch and high pitch.
Speed Compensation
This function is used to cancel the reaction that is
generated by the difference of the operation amount
of each servo when the swash-plate moves.
Swash AFR setting procedure
The swash AFR function makes adjustments
so that the servos travel the specified amount
by [AILERON], [ELEVATOR], and [PITCH]
operation.
8VH WKH (',7 GLDO WR PRYH WKH FXUVRU WR WKH
IXQFWLRQ \RX ZDQW WR DGMXVW DQG SXVK WKH
(',7EXWWRQWRVZLWFKWRWKHGDWDLQSXWPRGH
$GMXVWWKH$)5UDWHE\WXUQLQJWKH(',7GLDOWR
WKHOHIWRUULJKW
 ,QLWLDOYDOXH 
 $GMXVWPHQWUDQJH a
(When the EDIT button is pushed for 1 second, the AFR rate
is reset to the initial value.)
 3XVKWKH(',7EXWWRQWRHQGDGMXVWPHQWDQG
UHWXUQWRWKHFXUVROPRYHPRGH
ŏ6HOHFW>6:$6+@DWWKHOLQNDJHPHQXDQGFDOOWKH
VHWXS VFUHHQ VKRZQ EHORZ E\ SXVKLQJ WKH (',7
EXWWRQ
ŏ3XVK WKH S1 EXWWRQ WR
FDOOQH[WSDJH