Martin Christ RVC 2-18 CDplus - Manual (Page 60)

RVC 2-18 CD& HCL
8 Maintenance and service
60
Version 04/2012, Rev. 1.4 of 25/11/2013 • sb
Translation of the original operating manual
• Replace any damaged components immediately for your own safety.
• Immediately rinse off the rotors or accessories if any liquids that may
cause corrosion come into contact with them.
• Clean the accessories outside the rotational vacuum concentrator once
a week or preferably after each use.
• If the rotors or accessories have been contaminated with toxic,
radioactive, or pathogenic substances, clean them immediately with a
suitable decontamination agent (depending on the type of
contamination). Take suitable precautions for your own safety if there is
a risk of toxic, radioactive, or pathogenic contamination.
Pos: 168 /01 0 Univ ersal mod ule/ Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1
Pos: 169 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /08 0 Wart ung un d Inst and haltu ng/ 080 -001 0- 0030 -00 10 Alumini umzu beh ör @ 8\ mod _131 002 678 982 9_6 8.doc x @ 4 727 8 @ 4 @ 1
8.1.4.1 Aluminium accessories
Especially aluminium parts are susceptible to corrosion.
• Acid-containing cleaning agents and alkaline cleaning agents must be
avoided.
• Grease aluminium parts at least once a week with slushing oil for the
protection against corrosion.
This essentially increases their service life and reduces susceptibility to
corrosion.
Pos: 170 /01 0 Univ ersal mod ule/ Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1
Pos: 171 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /08 0 Wart ung un d Inst and haltu ng/ 080 -001 0- 0040 Glas br uch @ 8\m od_ 131 002 690 5087 _68 .docx @ 4 728 5 @ 3 @ 1
8.1.5 Glass breakage
CAUTION
In the case of glass breakage, immediately remove all glass particles (e.g.
with a vacuum cleaner). Replace the rubber cushions since even thorough
cleaning will not remove all glass particles.
Glass particles will damage the surface coating (e.g. anodising) of the
buckets, which will then lead to corrosion.
Glass particles in the rubber cushions of the buckets will cause glass
breakage again.
Glass particles on the pivot bearing of the load- bearing bolts prevent the
buckets and rotor blocks from swinging evenly, which will cause an
imbalance.
Glass particles in the rotor chamber will cause metal abrasion due to the
circulation. This metal dust will not only pollute the rotor chamber, rotor,
and materials to be evaporated but also damage the surfaces of the
accessories, rotors, and rotor chamber.
In order to completely remove the glass particles and metal dust from
the rotor chamber
• Grease the upper third of the rotor chamber with e.g. Vaseline.
• Then, let the rotor rotate for a few minutes at maximum speed and
atmospheric pressure. The glass and metal particles will now collect at
the greased part.
• Remove the grease with the glass and metal particles with a cloth.
• If necessary, repeat this procedure.
• Clean the rotor shaft.
Pos: 172 /01 0 Univ ersal mod ule/ Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1 Pos: 173 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /08 0 Wart ung un d Inst and haltu ng/ 080 -002 0 D esinfek tion v on R otork am mer un d Z ube hör @ 8\ mod _13 100 270 5588 9_6 8.d ocx @ 472 92 @ 2 @ 1