Yaskawa AC Drive-P1000 Industrial Fan - Manual (Page 564)

Run command selection while in Programming Mode .................... 151
Run Command Source Selection ............................................. 463
RUN Key ........................................................................ 109
RUN LED........................................................................ 111
RUN Light ....................................................................... 109
S
S- ....................................................................................96
S: Special Application.......................................................... 274
S: Special Parameters .......................................................... 452
S/L2.................................................................................83
S+ ...................................................................................96
S1 ...................................................................................94
S1: Dynamic Noise Control Function........................................ 452
S1-L21..............................................................................83
S2 ...................................................................................94
S2: Programmable Run Timers ......................................... 275, 452
S3 ...................................................................................94
S4 ...................................................................................94
S5 ...................................................................................94
S6 ...................................................................................94
S7 ...................................................................................94
S8 ...................................................................................94
Safety Hazard Definitions .......................................................18
Safety Information................................................................18
SC .............................................................................94, 307
S-Curve Characteristics .................................................. 177, 290
SE ................................................................................. 316
Search Operation Voltage Limit .............................................. 175
Secondary PI (PI2) Control.................................................... 280
Secondary PI Disable Mode............................................. 282, 455
Secondary PI Display Digits ............................................ 281, 454
Secondary PI Enable Selection ......................................... 280, 454
Secondary PI Feedback Detection Selection .......................... 283, 455
Secondary PI High Feedback Detection Time ........................ 283, 455
Secondary PI High Feedback Level .................................... 283, 455
Secondary PI Integral Limit Setting.................................... 282, 455
Secondary PI Integral Time Setting .................................... 281, 455
Secondary PI Low Feedback Detection Level ........................ 282, 455
Secondary PI Low Feedback Detection Time ........................ 283, 455
Secondary PI Output Level Selection .................................. 282, 455
Secondary PI Output Lower Limit ..................................... 282, 455
Secondary PI Output Upper Limit...................................... 282, 455
Secondary PI Proportional Gain Setting ............................... 281, 455
Secondary PI Setpoint Value............................................ 281, 455
Secondary PI Unit Selection ............................................ 281, 455
Secondary PI User Display .............................................. 280, 454
Second Line Monitor Selection ............................................... 449
Self-diagnosing function of the serial communication interface circuits 516
Sequence Timer 1............................................................... 275
Sequence Timer 1 Day Selection ............................................. 452
Sequence Timer 1 Reference Source......................................... 452
Sequence Timer 1 Selection................................................... 452
Sequence Timer 1 Start Time ................................................. 452
Sequence Timer 1 Stop Time ................................................. 452
Sequence Timer 2 Day Selection ............................................. 453
Sequence Timer 2 Reference Source......................................... 453
Sequence Timer 2 Selection................................................... 453
Sequence Timer 2 Start Time ................................................. 453
Sequence Timer 2 Stop Time ................................................. 453
Sequence Timer 3 Day Selection ............................................. 453
Sequence Timer 3 Reference Source......................................... 453
Sequence Timer 3 Selection................................................... 453
Sequence Timer 3 Start Time ................................................. 453
Sequence Timer 3 Stop Time ................................................. 453
Sequence Timer 4 Day Selection ............................................. 454
Sequence Timer 4 Reference Source......................................... 454
Sequence Timer 4 Selection................................................... 454
Sequence Timer 4 Start Time ................................................. 453
Sequence Timer 4 Stop Time ................................................. 454
Sequence Timer Error .......................................................... 320
Sequence Timers 1/2/3/4 Reference Source................................. 279
Sequence Timers 1/2/3/4 Selection........................................... 279
Sequence Timers 1 to 4 Day Selection....................................... 279
Sequence Timers 1 to 4 Start Time........................................... 278
Sequence Timers 1 to 4 Stop Time ........................................... 279
Sequence Timers 2 to 4 ........................................................ 276
SEr ................................................................................ 308
Serial Communications Cable Connection Terminals (TB5) ............. 486
Serial Communication Terminals...............................................96
Serial Communication Transmission Error ................................. 312
Serviceable Parts................................................................ 370
Set Time.......................................................................... 116
Setup Group Parameters ....................................................... 122
Setup Groups .................................................................... 117
Setup Modes..................................................................... 118
Shielded Twisted-Pair Cables ...................................................98
Side-by-Side Installation.........................................................49
Side-by-Side Mounting ........................................................ 411
Side-by-Side Setup ...............................................................49
Simplified Setup Using the Setup Groups................................... 118
Single Drive KEB Ride-Thru 1 ............................................... 240
Single Drive KEB Ride-Thru 2 ............................................... 240
Sinking/Sourcing Mode for Digital Inputs ....................................94
Slave Address ................................................................... 494
Slip Compensation.............................................................. 178
Slip Compensation Gain ....................................................... 178
Slip Compensation Limit ...................................................... 178
Slip Compensation Primary Delay Time .................................... 178
Slip Compensation Selection during Regeneration ........................ 178
SN...................................................................................94
Soft Charge Bypass Relay Maintenance..................................... 462
Soft Charge Bypass Relay Maintenance Time.............................. 314
Soft CLA Selection ............................................................. 446
Soft Starter Speed Reference at Previous Fault............................. 460
Software Current Limit Selection ............................................ 260
Software No. (Flash) ........................................................... 459
Software No. (PWM)........................................................... 459
Software No. (ROM) ........................................................... 459
Software version ..................................................................31
Space Between Drives (Side-by-Side Mounting) ............................49
Speed Agree 1 Time Chart .................................................... 216
Speed Agree 2 Time Chart .................................................... 219
Speed Agree Detection Selection............................................. 253
Speed Agreement Detection Level ..................................... 252, 444
Speed Agreement Detection Level (+/-)............................... 252, 444
Speed Agreement Detection Width .................................... 252, 444
Speed Agreement Detection Width (+/-) .............................. 252, 445
Speed Control Range ........................................................... 405
Speed Estimation Type Speed Search........................................ 154
Index
564 YASKAWA SIEP YAIP1U 01B AC Drive - P1000 Technical Manual