GE GEFanuc Automation Programmable Control Products TCP/IP Ethernet Communications for the Series 90t-70 PLC GFK-1004B User Manual
Page 57
3
3-5
GFK-1004B
Chapter 3 The GEnet System Manager–Station Configuration
Installing the PC Network Card (for Network GSM Operation)
The table below lists the 802.3/Ethernet cards that GE Fanuc has tested for proper net-
work GSM operation. If you wish to access stations from the GSM across the network,
you must have a network card or PCMCIA adapter in your PC. The PC network card
must support NDIS (Network Driver Interface Specification). If you use a PC network
card not in the list below, GE Fanuc cannot guarantee proper operation of the GSM.
Table 3-1. 802.3/Ethernet Cards for the PC
ББББББББ
ББББББББ
Vendor
ББББББББ
ББББББББ
Model
БББББ
БББББ
Size
БББББ
БББББ
PC Bus
БББББ
БББББ
Width
ББББББББ
ББББББББ
3Com
ББББББББ
ББББББББ
Etherlink II
t
(3C503)
БББББ
БББББ
Half slot
БББББ
БББББ
XT, AT
БББББ
БББББ
8-bit
ББББББББ
ББББББББ
3Com
ББББББББ
ББББББББ
Etherlink 16
t
(3C507)
БББББ
БББББ
1 slot
БББББ
БББББ
XT, AT
БББББ
БББББ
8-bit
ББББББББ
ББББББББ
3Com
ББББББББ
ББББББББ
Etherlink/MC
t
(3C523)
БББББ
БББББ
1 slot
БББББ
БББББ
Micro Channel
БББББ
БББББ
8-bit
ББББББББ
ББББББББ
SMC
/Western Digital
ББББББББ
ББББББББ
EtherCard PLUS
t
БББББ
БББББ
Half slot
БББББ
БББББ
XT, AT
БББББ
БББББ
8-bit
ББББББББ
ББББББББ
SMC/Western Digital
ББББББББ
ББББББББ
EtherCard PLUS Elite 16
t
БББББ
БББББ
1 slot
БББББ
БББББ
AT
БББББ
БББББ
16-bit
ББББББББ
ББББББББ
SMC/Western Digital
ББББББББ
ББББББББ
EtherCard PLUS/A
t
БББББ
БББББ
1 slot
БББББ
БББББ
Micro Channel
БББББ
БББББ
16-bit
ББББББББ
ББББББББ
Intel
ББББББББ
ББББББББ
Intel
82593
БББББББББББББ
БББББББББББББ
Interface is built-in to Zenith Z-note
t
PC
ББББББББ
ББББББББ
ББББББББ
Xircom
ББББББББ
ББББББББ
ББББББББ
Xircom
ϖ
Pocket Adapter
БББББ
БББББ
БББББ
External
БББББ
БББББ
БББББ
Enhanced
Printer Port
БББББ
БББББ
БББББ
N/A
ББББББББ
ББББББББ
NDIS supporting
network card
ББББББББББББББББББББ
ББББББББББББББББББББ
Vendor-dependent
t Etherlink II, Etherlink 16, and Etherlink M/C are trademarks of 3Com Corporation.
t EtherCard PLUS, EtherCard PLUS Elite16, and EtherCard PLUS/A are trademarks of Western Digital Corp.
t Z-Note is a trademark of Zenith Data Systems.
Intel is a Registered Trademark of Intel Corporation.
Xircom is a Registered Trademark of Xircom Incorporated.
SMC is a Registered Trademark of Standard Microsystems Corporation.
Note
The PC can lock-up if you make setup errors when installing PC
network cards and device drivers in a PC. Be sure you have a system
boot diskette to recover from possible setup errors.
When installing the network card in your PC, be sure to do the following.
1.
Install the network card into the computer according to the manufacturer’s
instructions. Setup the hardware as described in the table below; these are the
default settings of the card. If you do not use the default settings, you will need to
record your settings for later use in the section, “Setting-Up DOS System Files”.