Integra DPS-10.5 - Manual (Page 87)

87
Controlling Other Components —Continued
The DPS-10.5’s remote controller can learn individual
commands from other component’s remote controllers
and then be used to control those components. Com-
mands can be learnt by the dedicated leaning buttons—
[L1], [L2], [L3], and [L4]—or any button. Each button
can learn up to four commands, one for each remote con-
troller mode: DVD, Amp, VCR, and TV.
If you’ve entered a control code for a component
(page 82) and certain buttons don’t work as expected,
you can also use this function to program those buttons
individually.
Notes:
• The following buttons cannot learn new commands:
[LIGHT] and the [DVD], [Amp], [VCR], and [TV]
Mode buttons.
• Learning mode is cancelled automatically if you don’t
press any buttons for 30 seconds.
• The DPS-10.5’s remote controller comes prepro-
grammed with the commands necessary for control-
ling Integra DVD players (DVD mode) and AV
receivers (Amp mode). However, you can reprogram
individual buttons if necessary. The original com-
mands can be restored by resetting the remote
controller.
• To program a button that has already learnt a com-
mand, repeat this procedure. The previously learnt
command will be overwritten.
• Like most remote controllers, the DPS-10.5’s remote
controller uses infrared. Commands from remote con-
trollers that don’t use infrared cannot be learnt.
• When the remote controller’s batteries expire, all
learnt commands may be lost and will have to be learnt
all over again, so keep your other remote controllers in
a safe place.
Learning the Commands of Other
Remote Controllers
1 Point the remote controllers at each other,
about 2 to 6 inches (5–15 cm) apart.
2 While holding down the [DVD], [Amp],
[VCR], or [TV] Mode button, press the [On]
button, and then release both buttons.
The Mode button and Tx/Learn indicator light up.
+10 0 Clear
1 2 3
4 5 6
7 8 9
Input I
+
-
Enter
Set up Retu rn
L 4
L 2 L1 V Off V In
Aspect A-B Repeat
Rsltn Angle Subtitle Audio
L 3
To p M enu Men u
VOL
+
-
V3
TV
Input D M S
DVD Amp VCR
DVD V1 V 2
LM RD
Zoom
CH
L Mode
Learning
Search Memory Dimmer Amp Input
Display
Audio
Sel
Zoom On Picture Control
Random Step/Slow
Muting
Angle Subtitle Audio
Aspect A-B Repeat
On Standby T V
T V CH
T V VOL
RC-562DV
Last Memory
Resolution
Mode
Amp Input
Rec
Open/Close
Video Input Video Off
On
Mode
PO W ER SL EE P D IM M ER SU R M O D E
VI D EO -1 VID EO -2
TA PE
D VD
C D
C D
D VD
TU N ER
TU N ER
PH O N O
IN PU T SE LE C TO R
D IS C
TA PE
VO LU M E
LE VE L
C H S EL
PR ES ET
M U TI N G
TE ST TO N E
M UL TI- CH IN PU T
R EM O TE C O N TR O LLE R
G R O U P
R C -3 85 S
2–6" (5–15 cm)
RC-563DV
3 On the DPS-10.5’s remote controller, press
the button that you want to learn the new
command.
The Tx/Learn indicator goes off while the button
is being pressed, and comes back on again when
it’s released.
Use the dedicated leaning buttons—[L1], [L2],
[L3], and [L4]—or another button.
4 On the other remote controller, press and
hold the button whose command you want
to learn until the Tx/Learn indicator
flashes.
If the command is learnt successfully, the Tx/
Learn indicator flashes slowly twice, and then the
Mode button and Tx/Learn indicator remain lit.
If the Tx/Learn indicator flashes quickly three
times, the command has not been learnt, in which
case you should try again from step 3.
If the Tx/Learn indicator flashes quickly six times,
the remote controller’s memory is full and no
more commands can be learnt.
5 To learn more new commands, repeat
steps 3 and 4.
When you’ve finished, press the Mode button that
you pressed in step 2.
To use the learnt command, select the relevant
mode, and then press the button.