Toshiba RAV-SM1100UT-E - Manual (Page 55)

52
HO
W T
O
OPERA
TE THE
UNIT
Cool/Heat A
U
T
O
, Heat,
Dry
, Cool,
F
a
n
P
o
wer suppl
y
T
u
rn
on the po
w
er of the wireless remote controller 12 hours bef
ore star
ting the oper
ation.
•
After the po
wer supply has been tur
ned on, the oper
ation of the remote controller is not
accepted f
or appro
x.
1 minute
. It is not a f
ailure
.
(The sensor receiv
es the signal once
, b
ut the receiv
ed contents are cleared.)
4
Push either
or
to select the desired temperature
.
•
Dur
ing F
AN mode
, the temper
ature cannot be set up
.
5
Stop Push Star
t/Stop b
utton.
When using the remote controller to stop the unit, the outdoor unit f
an ma
y k
eep oper
ating f
o
r
a while e
v
en if the compressor of the outdoor unit has stopped.
•
In heating
operation,
if
the
room
is
not
comf
o
r
ta
b
ly
heated
with
F
A
N
, select
F
A
N
or
.
Although the
y are displa
y
ed, the function ma
y not be pro
vided according to the used indoor
unit.
(F
an speed is constant.)
•
When the unit
cannot
be
stopped
b
y
the normal
operation
T
u
rn
off the po
wer s
witch
or leakage
break
e
r, and then contact the shop which y
ou purchased
the unit. A
utomatic cool/heat
When all indoor units in the identical refr
iger
ant system are controlled as a group
, the cooling/
heating oper
ation is automatically perf
o
rmed with the diff
erence betw
een the setup temper
ature
and the room temper
ature.
Dry operation
•
There is no dr
y function according to the used indoor unit e
v
en if DR
Y is displa
y
ed on the
displa
y section of the remote controller
. (Same to Cooling oper
ation)
•
When the room temper
ature approaches the setup temperature
, r
unning/stop oper
ations are
automatically repeated.
•
In order not to retur
n humidity to the room as possib
le, the mode of indoor f
an enters LO
W
mode when the oper
ation has stopped.
•
The f
an speed cannot be adjusted according to the used indoor unit or status of the room
temperature.
•
The DR
Y mode cannot be used according to the used indoor unit when the outdoor temper
a
-
ture is 15
˚C or
lo
we
r.
1
Push Star
t/Stop
b
utton.
2
Push
(Operation Select b
utton)
operation to select one of
,
,
,
, and
.
3
Push
(F
an Mode Select b
utton)
to select one of fan speed modes. When selecting
, the f
an speed is
automatically changed. (Dur
ing F
AN mode
, the air speed is
not automatically changed.)
3
4
2
1
HO
W T
O
OPERA
TE THE TIMER
•
After setting of the timer
, set the remote controller at a position where the signal can reach the
sensors (indoor unit body) . (The signal of the timer oper
ation is sent from the remote controller
.)
•
Set up the timer dur
ing displa
y of the oper
ation mode
.
Use in the f
ollo
wing cases
T
o
stop the air conditioner
after the pre
viously set time
has passed T
o
stop the air conditioner
e
v
er
y time after the pre
viously
set time has passed T
o
operate the air conditioner
after the pre
viously set time
has passed
During displa
y
Timer time
Ev
er
y pushing
, the setup time increases b
y
0.5 hour (30 min
utes).
The maxim
um time to be set is 72.0 hours
.
Ev
er
y pushing
, the setup time decreases b
y
0.5 hour (30 min
utes).
The minim
um time to be set is 0.5 hours
.
Timer displa
y
Ev
er
y pushing
SET
, the displa
y changes as
follo
ws;
<Use e
xample>
H
o
w to use OFF timer
(Ex.)
T
o
stop the unit 30 min
utes after
1
W
hen pushing the timer
SET
once
,
and the time flash on the remote
contr
oller
.
2
Push TIME
or
to set the time
to 0.5.
3
Push
SET
and the
go on timer
.
H
o
w to use the repeat timer
(Ex.)
T
o
stop the air conditioner e
v
e
ry time
after 2.5 hours has passed
1
When pushing the timer
SET
twice,
,
and the time flash on the
remote contr
oller.
2
P
ush TIME
or
to set the time
to 2.5.
3
Push
SET
and the
,
go
on
timer
.
The
wo
rk
s
,
and the operation stops
after 2.5 hours
. When pushing
(Star
t/Stop)
b
utton again to oper
ate the
unit, the operation stops after 2.5 hours
.
H
o
w to use ON timer
(Ex.)
T
o
oper
ate the unit 8 hours after
1
When pushing the timer
SET
three
times,
and the timer flash on the
remote contr
oller
.
2
Push TIME
or
to set the time
to 8.0.
3
Push
SET
The operation mode displa
y disappears
,
and then time and the
go on.
T
o
stop the timer operation
T
o
stop the timer operation
Push
C L
b
utton.
Then the timer displa
y
disappears
.
ADR
No display