Address – Toshiba RAV-SM1100UT-E User Manual
Page 57
54
HO
W
T
O
HANDLE
THE REMO
TE CONTR
OLLER
•
Direct the tr
ansmitter of the remote controller to
w
ard the sensor (indoor unit body).
When the signal is nor
mally receiv
ed,
“Pi
” sound is heard once
.
(“
Pi, pi
” sounds are heard only when the oper
ation has star
ted.)
•
The standard distance which the signal can be receiv
ed is appro
x.
7m.
The distance diff
ers a little according to the capacity of the batter
y,
etc.
•
Be careful there is not something to b
loc
k the signal between the sensor (indoor unit body)
and the remote controller
.
•
Do not put the remote controller on the place e
xposed to the direct sunlight or air from the air
conditioner or near the sto
v
e
, etc.
•
Do not drop
, thro
w
, or clean with w
ater the remote controller
.
•
The signal ma
y be accepted in a room where the electronic instantaneous-ON type or
in
v
e
rter type florescent light is set.
F
or details
, contact the shop which y
ou purchased the air
conditioner
.
T
o
Use the Remote Contr
oller Setting to
W
all,
etc.
•
Chec
k a signal is receiv
ed correctly b
y
pushing
Star
t/Stop b
utton at the position to be
fix
ed.
•
T
o
tak
e off remote controller
, pull it to
w
ard y
ou.
HO
W T
O
USE THE
REMO
TE
CONTR
OLLER
CORRECTL
Y
•
Set the remote contr
oller so that it is not e
xcessivel
y far fr
om the sensor
(indoor unit), otherwise a malfunction is caused.
Be sure to set the remote controller in the same room where the sensor (indoor unit) is
installed.
•
Direct the remote contr
oller to
war
d the sensor (indoor unit) f
or operation.
When a signal is correctly receiv
ed,
“Pi
” sound can be heard.
•
A
v
oid to set the remote contr
oller at a place where it is co
vered with cur
tain,
etc.
1
2
Mounting scre
w
T
russ tapping
Put on.
Push.
Fix the remote controller
holder with the scre
ws.
Setting method of
remote controller
Remote controller holder
ADDRESS
When the m
ultiple indoor units corresponding to the wireless remote contr
oller are
installed in the same r
oom,
an ad
dress can be set up to pre
vent an interf
erence
.
Matc
hing the ad
dress s
witc
h of the sensor with n
umber of the remote contr
oller ad-
dress,
Max.
6 indoor units can be contr
olled b
y
the corresponding
remote contr
oller
individuall
y.
The ad
dress s
witch f
or receiving the signal is prepared to the sensor (inside of panel or
indoor unit) and the ad
dress s
witc
h f
or sending the signal is prepared to the remote
contr
oller
. For details,
contact the shop whic
h y
ou pur
c
hased the air conditioner
.
Ho
w to Chec
k the Ad
dress
When pushing
ADR
b
utton on the remote controller
, the present address is displa
y
ed on the
displa
y section of the remote controller
. If this address matches with the address of the sensor
(inside of panel or indoor unit), a b
uzz
er sounds
.
(When ALL is displa
y
ed, b
uzz
er sound is necessar
ily heard.)
When ALL is displa
y
ed, the air conditioner can be oper
ated regardless of an
y address of the
sensor (inside of the indoor unit).
Send the signal b
y
directing the remote controller to
w
ard the
sensor (panel or indoor unit body) to be handled.
Ho
w to Matc
h the Ad
dress
Setup to remote controller address
1.
When k
eeping
ADR
pushed f
or 4 seconds or more
,
ADR
lamp goes on at the displa
y
section of the remote controller and the present address is displa
y
ed with flashing.
2.
Ev
er
y pushing
ADR
, the address is e
xchanged as ALL
1
2
3
…
6
ALL.
Match
one of them with the address s
witch of the indoor unit sensor to be handled.
3.
When pushing
C L
, the address displa
y goes on and is displa
y
ed f
or 5 seconds
.
If the address matches with the address s
witch of the oper
ation par
t, the b
uzz
er sounds
.
S001
4
–
6
S002
3 6
2 5
1 4
Address
select
Address
S002
3 6
2 5
1 4
Address
S002
3 6
2 5
1 4
Address
S001
4
–
6
Address
select
S001
4
–
6
Address
select
Displa
y of
remote
controller
address
Address s
witch
position of
sensor
*
Address s
witch
of sensor unit
can be set an
y
position.
Address
Address
Address
Address
1
–
31
–
3
1
–
3
T
u
rn
the knob to the r
ight side f
or 1 to 3 while to the left side f
or 4 to 6 of Address select s
witch
S001.