Franklin Fueling Systems TS 550 evo Fuel Management System Programming Guide - Manual (Page 27)

27
Programming FMS Parameters
Here is where specific equipment parameters will be modified to match the site setup.
Fuel Management System
Group Name Parameter Name
Parameter
Default
Description
Parameter
Input
Fuel Management
System
Ullage Percent (95) Percent of tank level used to calculate space left. 70-100 %
Delivery Delay (15 min) Time in minutes after delivery when increase is reported. 1 - 240
Correction Temperature (60.00 °F) Product temperature correction. 5 - 100 °
High Product Limit (Level)
Select whether the High Product alarm will be triggered
by high product Level or high product Volume.
Level / Volume
Static Tank Testing
Region (United States) The region in which the gauge is located
Other
United States
Spain
Monthly Leak Test Threshold (0.20 gph) Static leak tolerance for testing tanks. 0 - 10
Yearly Leak Test Threshold (0.10 gph) Static leak tolerance for testing tanks. 0 - 10
Sentinel Mode Threshold * (3.00 gph)
If Sentinel Mode is configured, this is the amount of
volume that would trigger an alarm.
0 - 10
Confidence (99%) Leak testing confidence.
90, 95, 97.5,
99 %
Minimum Leak Test Time (2 hr) Minimum amount of time used to test. 0-8
Maximum Leak Test Time (8 hr) Maximum amount of time used to test. 1-8
Alarm On Precision Leak Test
Failure *
(No)
Used to produce an alarm upon failure.
Yes/No
Tanks Number of Tanks (0) Number of tanks in fuel system. 0-48
Tank #
Name (Tank 1) Given name of tank. abc#
Type (Special 1) Type of tank. Std./Spcl.
Manifolded (No) Used for Manifolded tanks. Yes / No
Manifold # (1)
If Manifold is selected, this option will allow you to
select a manifold number. Tanks that are Manifolded
should have the same manifold number.
1 - 24
Product # ( 1) Type of product in tank. 1-48
Delivery Threshold (200.0 gal) Amount of increase to report delivery. 0.3 - 9,000,000
Theft Threshold (5.0 gal) Amount of decrease to report theft. 0.3 - 9,000,000
4-20 mA Output (None)
If an IO module is used and the outputs are configured,
this option will appear. Select the correct output that
correlates to this tank.
None
Output 1-24
Monthly Compliance (Yes)
Select Yes if this tank is to appear on the Compliance
page and in the Regulatory report.
Yes / No
Annual Compliance (Yes)
Select Yes if this tank is to appear on the Compliance
page and in the Regulatory report for annual tank testing.
Yes / No
Probe Channel (Probe 1) Channel used for the probe in tank. Probe
Type (Standard 101) Type of probe used in this tank. Std./Spcl.
Ratio
(1 to 1 tip to
head)
Ratio of float movement in proportion to product level.
1:7-9 for use with Moorman gauge interface.
1:1, 7:1, 9:1
Float Type (4 in gas) Type of float(s) used on probe. 4, 3, or 2 in.
Gas/Diesel,
Stainless,
Propane
Gas density
Diesel Density
Water Float (Yes) Select Yes if water float is present. Yes /No
Gradient
(9.03000 µs / in) Speed of probe wire.
7 - 10
Product Offset (0.00 in)
Used for compensation of tank tilt. (See Appendix xx:
Calculating Tank Tilt).
-1,200,000 to
1,200,000
Water Offset (0.00 in)
-1,200,000 to
1,200,000
Generator
Mode
Enable (No) If generator testing is being used, select yes. Yes / No
SCALD Enable (No) Enables SCALD tank testing. Yes / No
Qualify (14 %) Required percent full to run SCALD test. # %
* These features are only available when Spain is selected for Region