Alpha Technologies PN-4 - Manual (Page 5)

5 031-103-B0-004, Rev. D
List of Figures
Fig. 1-1, PN-3 Specifi cations .............................................................................................................................. 8
Fig. 1-2, PN-4 Specifi cations .............................................................................................................................. 9
Fig. 2-1, Enclosure as it Arrives from Alpha ....................................................................................................... 9
Fig. 2-2, Packing Label Location ........................................................................................................................ 9
Fig. 3-1, Suggested Site Selection for PN-3 and PN-4..................................................................................... 10
Fig. 3-2, Single-Wide Concrete Pad for PN-3 and PN-4 ...................................................................................11
Fig. 3-3, Suggested Grounding, PN-3 and PN-4 .............................................................................................. 12
Fig. 3-4, Alternate Grounding, PN-3 and PN-4 ................................................................................................. 13
Fig. 3-5, PN-3 Mounted to the Prepared Pad ................................................................................................... 14
Fig. 4-1, BBX-100A-8POS Service Disconnect ................................................................................................ 16
Fig. 4-2, BBX-70A Service Disconnect ............................................................................................................. 17
Fig. 4-3, Schematic: Primary Service BBX-100A-8POS with IPP-240-3 .......................................................... 18
Fig. 4-4, Schematic: Primary Service BBX-100A-8POS with IPP-120-3 .......................................................... 18
Fig. 4-5, Schematic: Secondary Service BBX-100A-8POS with IPP-120-2 ..................................................... 19
Fig. 4-6, Schematic: Secondary Service BBX-100A-8POS with IPP-240-2 ..................................................... 19
Fig. 4-7, Schematic: Secondary Service BBX-70A with IPP-120-1 .................................................................. 20
Fig. 4-8, Schematic: Primary Service BBX-70A with IPP-240-1 ....................................................................... 20
Fig. 4-9, Conduit Location ................................................................................................................................ 22
Fig. 4-10, Coaxial Connectors .......................................................................................................................... 22
Fig. 4-11, Alpha Cell Battery Date Code ........................................................................................................... 23
Fig. 4-12, Terminal Connections ....................................................................................................................... 23
Fig. 4-13, Fuse Terminal Connection for Threaded Insert Batteries ................................................................. 24
Fig. 4-14, In-Line Fuse Link Mounting, Flag Terminal Batteries ....................................................................... 24
Fig. 4-15, Hardware Installation for Fuse Terminal on Threaded Insert Battery ............................................... 25
Fig. 4-16, Hardware Installation for Flag Terminal Connections ....................................................................... 25
Fig. 4-17, PN-3/PN-4 Battery Installation ........................................................................................................ 26
Fig. 4-18, Battery Temperature Sensor Mounting Location .............................................................................. 27
Fig. 5-1, Battery Interface Unit Installed ........................................................................................................... 29
Fig. 5-2, BBX 70A (BBX-FI2) ........................................................................................................................... 29
Fig. 5-3, BX 100A (BBX-FI8) ............................................................................................................................ 29
Fig. 5-4, MTS (Showing100A and 60A boxes).................................................................................................. 29
Fig. 5-5, BBX 100A (BBX-FI8) .......................................................................................................................... 29
Fig. 5-6, IPP for Three Power Supplies ............................................................................................................ 30
Fig. 5-7, IPP for Two Power Supplies ............................................................................................................... 30
Fig, 5-8, IPP for One Power Supply ................................................................................................................. 30
Fig. 5-9, Breaker Duplex Option (BDO) ........................................................................................................... 30
Fig. 5-10, LA-P+ Installed in BDO .................................................................................................................... 30
Fig. 5-11, Location of LED on LA-P+ ................................................................................................................ 30
Fig. 5-12, Cooling Fan Panel ........................................................................................................................... 31
Fig. 5-13, Panel Installed in Top Rear of Enclosure ......................................................................................... 31
Fig. 5-14, Cooling Fan Plugged into Power Supply and SPI ............................................................................ 31
Fig. 7-1, Single-wide Pad, for PN 3/4 ............................................................................................................... 33
Fig. 7-2, Double-wide Pad, for PN 3/4 .............................................................................................................. 34
Fig. 7-3, Double-wide Pad, for CE 3x2/9x2 and CE8/9 or PN 3/4 .................................................................... 35