intimus 100 CP7 - Manual (Page 4)

SCOPE OF APPLICATION:
The document shredder intimus 100SP2/CP4/
CP5/CP6/CP7 is a machine for the destruction
of common written material.
The machine may only be used to
shred paper!
Shredding of other types of data carriers
and also of staples and paper clips with
the models with cutting width 0.8x12 mm
(CP6) or 0.8x4.5 mm (CP7) may lead to
injuries (for example due to splintering of
hard materials etc.) and damage to the
machine (for example destruction of the
cutter etc.).
INSTALLATION:
- Unpack and set machine upright.
- Place plastic sack into the receptacle.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA“.
The air vents in the housing are ne-
cessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
IMPORTANT SAFETY NOTES
CONTROLS:
1 = Pushbutton switch (fig. 1)
“Ready”/ “Off”
This button has two functions:
a) “Ready”
The machine changes to “Ready” if you
press this button briefly.
b) “Off”
The machine switches off if it is in the
“Ready” mode and the button is held
down for about 3 seconds.
Note: The machine switches off
automatically if it is not used for about 5
minutes.
2 = Light barrier (forward operation) (fig. 2)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
3 = Pushbutton switch (fig. 1)
„Backward operation“ / „Stop“
This button has two functions:
a) “Backward operation”
If this switch is pressed, the shredding
mechanism runs in reverse.
b) “Stop”
If you briefly press this button while
the cutting mechanism is running, it is
switched off and stops.
Note: If pressed again when the
light barrier is activated, the cutting
mechanism will run forwards again and
continues with the shredding process.
4 = Pilot lamp (fig. 1)
„ready“
Lights when the pushbutton switch (1) is
operated.
5 = Pilot lamp (fig. 1)
„receptacle full“ / „door open“
a) Flashes when the receptacle is full and
needs to be emptied. At the same time
the machine switches off automatically.
b) Lights when the door is not closed. The
machine then switches off automatically
and it cannot be started as long as the
door is open.
6 = Pilot lamp (fig. 1)
„Paper jam“ / „Stop“
Lights up, if
a) too much paper has been fed into the
cutting mechanism. The shredding
mechanism jams and stops. The motor is
switched off.
b) while the cutting mechanism is running,
the pushbutton switch (3) is pressed. The
cutting mechanism is switched off and
stops.
FEEDING OF SHEETS:
- Turn machine on with pushbutton switch (1)
(fig. 1). Pilot lamp lights up (4) (fig. 1).
- Feed paper through the inlet guide to the cutting
system.
- Machine switches automatically to forward
and draws paper in. The machine switches off
automatically after shredding.
Note: In order to always obtain a correct cutting
result in terms of particle size and thus achieve
the safety class according to DIN 66399 as
stated in the brochure, the material to be cut
must always be fed into the cutting mechanism
at a right angle to the cutting mechanism and in
appropriate quantities in the middle of the inlet
slot.
Never feed the shredder with a quantity
of paper exceeding the maximum indi-
cated in the technical details!
Should the machine be overfed, follow the
instructions under „PAPER JAM“.
93047 1 07/13
4 6 1 3 5
100SP2 100CP4 100CP5 100CP6 100CP7
2
GB
4
fig. 1 fig. 2 fig. 3
OPERATION
OPERATION
INITIATION
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung