Gilderfluke&Co 8 Bit Digital Audio Systems - Manual (Page 28)

This feature defaults to an 'off' condition.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"p" PA Zone Priorities:
NOT USED WITH AB-100 AudioBrick: In the Public Address System there
are a number of different ways to assign priorities to different PA STATIONS
and PA zones. If STANDARD and ZONE PRIORITIES are both off, then all valid
PA requests (from PA STATIONS other than the top and second priority PA STA-
TIONS for this card) will be treated equally. Any valid request will be hon-
ored, and if more than one valid request comes in to the same card, they
will simply be mixed.
If the PA ZONE PRIORITY option is 'on', then PA zone requests with higher
numbers will take priority over those with lower numbers. Only one PA re-
quest will be honored at one time.
This feature defaults to an 'off' condition.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"q" Loop All:
Under normal looping mode, a single spiel will repeat over and over
again. If this feature is 'on', all the spiels recorded on a single card will be
played in a loop. A delay, if enabled, will be inserted between each indi-
vidual spiel.
This feature defaults to an 'off' condition.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"G" Group Assignments:
When using the serial port to control the audio system, you have the
choice of using a number of commands (start, stop, etc.) which select only
a single 'group' of cards. This command is used to select which of 12
GROUP ASSIGNMENTS this card will respond to.
Acceptable input range for GROUP ASSIGNMENTS are from 0 to F. If you
need less than 12 GROUPS, you should assign the unused spaces to any of
the group numbers you have already used.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"H" PA Zone Enables:
NOT USED WITH AB-100 AudioBrick: You can tell any card in the system
to respond to up to 8 different PA zone requests. This command is used to
tell the card which zones it should respond to. Any PA requests to a zone
other than ones which has been assigned to it will be ignored by this card.
Acceptable input range for ZONE ASSIGNMENTS are from 00 to FF. If you
need less than 8 ZONES, you should assign the unused spaces to any of the
PA ZONE numbers to FF.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"I" Half-Mute Zone Enables:
NOT USED WITH AB-100 AudioBrick: There are eight HALF-MUTE zones
available in the Digital Audio System. This command is used to select which
of the eight, if any, you wish to use. Any HALF-MUTE request for an enabled
HALF-MUTE ZONE will half-mute this card.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"J" Full-Mute Zone Enables:
There are eight FULL-MUTE zones available in the Digital Audio System.
This command is used to select which of the eight, if any, you wish to use.
Any FULL-MUTE request for an enabled FULL-MUTE ZONE will mute this card.
G ILDERFLUKE & C O . ¥ 205 S. F LOWER ¥ B URBANK , C A 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ F AX 818/840-9485
20 of 72