Gilderfluke&Co 8 Bit Digital Audio Systems User Manual
Page 37
fies the operation of this one card and no other parts of the system.
EXAMPLE: to put card 00 into ECHO ALL mode:
e 0 0
EXAMPLE: a 'Start Track# 00' command will echo:
t00
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"f"
Exit Echo All Mode:
This command takes all cards in the system out of ECHO ALL MODE.
EXAMPLE: to take any and all cards out of ECHO ALL mode:
f
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"g"
Enter Echo Mode:
This command puts all the cards in the system into ECHO MODE. When in
this mode, all track-specific commands are echoed by the card addressed
by the command. This is the type of echo mode which best verifies the
proper operation of all the cards in the digital audio system.
EXAMPLE: to put card 00 into ECHO mode:
g 0 0
EXAMPLE: a 'Start Track# 00' command will echo:
t00
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"h"
Exit Echo Mode:
This command takes all cards in the system out of ECHO MODE.
EXAMPLE: to take any and all cards out of ECHO mode:
h
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
"i" (TRACK#)
Track Status Report:
This command responds with a stream of ASCII HEX data containing the
current status of the card specified by the TRACK#:
BYTE 1 &2 = LED Port Status
BIT 0 = MUTE STATUS (1 = muted)
BIT 1 = DELAY STATUS (1 = in delay)
BIT 2 = HALF-MUTE STATUS (1 = half-muted)
BIT 3 = not used
BIT 4 = RUN STATUS (1 = running)
BIT 5 = STATUS OUTPUT STATUS (1 = on)
BIT 6 = PA STATUS (1 = on)
BIT 7 = REPEATER CLOCK ENABLED (1 = on)
BYTE 3 & 4 = INPUT STATUS
BIT 0 = A INPUT STATUS (1 = closed)
BIT 1 = B INPUT STATUS (1 = closed)
BIT 2 = PB INPUT STATUS (1 = closed)
BIT 3 = not used
BIT 4 = not used
BIT 5 = not used
BIT 6 = not used
BIT 7 = not used
BYTES 5 through 12 = Memory Address Status BITS 10 THROUGH 42
BYTE 13 & 14 = Dipswitch #1 Status
BYTE 15 & 16 = Dipswitch #2 Status
BYTE 17 & 18 = Aux. Port Status
BYTE 19 & 20 = PA TRUNKS 8 through 15
BYTE 21 & 22 = PA TRUNKS 0 through 7
BYTE 19 = CARRIAGE RETURN
BYTE 21 = LINE FEED
EXAMPLE: to poll the status for card 00:
i 0 0
3800000001290000000000
G
ILDERFLUKE
& C
O
.
¥
205 S. F
LOWER
¥
B
URBANK
, C
A
91502-2102
¥
818/840-9484
¥
800/776-5972
¥
F
AX
818/840-9485
29 of 72