Teledyne LeCroy PXA125 - Manual (Page 150)

User Manual PXA125
Programming Reference 4-32
SOURce
Subsystem This subsystem is used to control output functions, shape and
parameters, frequency, amplitude and amplitude modulation, and filter
type. Optional nodes were omitted from these commands. Factory
defaults after *RST are shown in bold typeface. Parameter low and
high limits are given where applicable.
Keyword Parameter Form Default,Low Limit,High
Limit
[:SOURce]
:APPLy (?)
:SINusoid (?) {<freq>,<ampl>,<offs>,<phase>}
:TRIangle (?) {<freq>,<ampl>,<offs>,<phase>}
:SQUare (?) {<freq>,<ampl>,<offs>,<duty_cycle>}
:PULSe (?) {<freq>,<ampl>,<offs>,<delay>,<rise>,<high>,<fall>}
:RAMP (?) {<freq>,<ampl>,<offs>,<delay>,<rise>,<fall>}
:SINC (?) {<freq>,<ampl>,<offs>,<N_cycles>}
:EXPonential (?) {<freq>,<ampl>,<offs>,<exp>}
:GAUSsian (?) {<freq>,<ampl>,<offs>,<exp>}
:DC (?) <%_ampl>
:USER (?) {<seg#>,<sclk>,<ampl>,<offs>}
:FM (?) {OFF|ON|0|1} OFF
:DEViation (?) <deviation> 1e6,100e-3,100e6
:FUNCtion
:MODE (?) {FIXed|USER} FIXed
:SHAPe (?) {SINusoid|TRIangle|SQUare|RAMP) SINusoid
:FREQuency <FM_freq> 1e3,1e-3,100e3
:RASTer (?) <FM_sclk> 1e6,1e-3,10e6
:TRIGger
:MODE (?) {CONTinuous|TRIGgered|GATed} CONTinuous
:SLOPe (?) {POSitive|NEGative POSitive
:FREQuency (?) {<freq>|MINimum|MAXimum} 1e6,100e-6,50e6
:RASTer (?) {<sclk>|MINimum|MAXimum} 10e6,100e-3,100e6
:SOURce (?) {EXTernal|INTernal} INTernal
:FSK (?) OFF|ON|0|1} OFF
:FREQuency
:RASTer (?) <FSK_sclk> 80e6,100e-3,100e6
:MODE (?) {HOP|RAMP} HOP
:RAMP
:TIME (?) <time> 1e-3,10e-6,1
:FUNCTion
:MODE (?) {FIXed|USER|SEQuence} FIXed
:SHAPe (?) {SINusoid|TRIangle|SQUare|PULSe|RAMP
|SINC|EXPonential|GAUSsian|NOISe|DC}SINusoid
:ROCSillator
:SOURce (?) (INTernal|EXTernal | TCXO) INTernal
:SWEep (?) OFF|ON|0|1} OFF
:STOP (?) <stop_sclk> 20e6,100e-3,100e6
:TIME (?) <time> 1e-3,1e-3,1000
:DIRection (?) (UP|DONW) UP
:SPACing (?) (LINear|LOGarithmic) LINear
:TRIGger
:MODE (?) {CONTinuous|TRIGgered|GATed} CONTinuous
:SLOPe (?) {POSitive|NEGative POSitive