Brocade Network OS Administrator’s Guide v4.1.1 - Manual (Page 459)

1. Use the show lldp command to display LLDP general information.
switch# show lldp
2. Use the show lldp command to display LLDP interface-related information.
The gigabitethernet rbridge-id/slot/port operand is used only for the Brocade VDX 6710, VDX
8770-4, and VDX 8770-8. The prompt for these ports is in the following format: switch(config-if-
gi-22/0/1)#.
switch# show lldp interface tengigabitethernet 0/1
LLDP information for gi 22/0/1
State: Enabled
Mode: Receive/Transmit
Advertise Transmitted: 30 seconds
Hold time for advertise: 120 seconds
Re ‑init Delay Timer: 2 seconds
Tx Delay Timer: 1 seconds tengigabitethernet
DCBX Version : CEE
Auto ‑Sense : Yes
Transmit TLVs: Chassis ID Port ID
TTL IEEE DCBX
DCBX FCoE App DCBX FCoE Logical Link
Link Prim Brocade Link
DCBX FCoE Priority Bits: 0x8
3. Use the show lldp command to display LLDP neighbor-related information.
switch# show lldp neighbors interface tengigabitethernet 0/1 detail
Neighbors for Interface Te 1/0/1
MANDATORY TLVs
===============
Local Interface: Te 1/0/1 (Local Interface MAC: 0027.f854.501e)
Remote Interface: TenGigabitEthernet 3/0/1 (Remote Interface MAC: 0005.334b.7198)
Dead Interval: 120 secs
Remaining Life : 117 secs
Chassis ID: 0005.334b.7173
LLDP PDU Transmitted: 1165 Received: 1164
OPTIONAL TLVs
==============
DCBX TLVs
==============
Version : CEE
DCBX Ctrl OperVersion: 0 MaxVersion: 0 SeqNo: 2 AckNo: 2
DCBX ETS OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 0
Enhanced Transmission Selection (ETS)
Priority-Group ID Map:
Priority : 0 1 2 3 4 5 6 7
Group ID : 0 0 0 0 0 0 0 0
Group ID Bandwidth Map:
Group ID : 0 1 2 3 4 5 6 7
Percentage: 0 0 0 0 0 0 0 0
Number of Traffic Classes supported: 8
DCBX PFC OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 0
Priority-based Flow Control (PFC)
Enabled Priorities: none
Number of Traffic Class PFC supported: 8
FCoE App OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 0
FCoE Application Protocol
User Priorities: none
FCoE LLS OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 0
FCoE Logic Link Status: Down
LAN LLS OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 0
LAN Logic Link Status: Up
Clearing LLDP-related information
To clear LLDP-related information, perform the following steps from privileged EXEC mode.
1. Use the clear command to clear LLDP neighbor information.
switch# clear lldp neighbors interface tengigabitethernet 0/1
2. Use the clear command to clear LLDP statistics.
switch# clear lldp statistics interface tengigabitethernet 0/1
Clearing LLDP-related information
Network OS Administrator’s Guide 459
53-1003225-04