Rockwell Automation SA3100 AC Power Modules - Manual (Page 118)

Index-2 SA3100 Power Modules
mounting the power module, 3-2 to 3-7
planning the installation, 3-1
power cabling, 3-11 to 3-12
selecting lug kits, 3-17 to 3-18
wiring, 3-18 to 3-19
Internal DC bus control, F-1 to F-6
bus control flowchart, F-4
bus protection, F-6
modifying DC bus voltage thresholds, F-5
operating range, F-5
Introduction, 1-1 to 1-6
Inverter power bridge, 2-2
Isolation transformer, 3-8
L
Line input disconnect, 3-9
Line reactor, 3-8
Lug kits, 3-17 to 3-18
M
Motor cables, D-1 to D-3
cable terminator, D-3
conduit, D-2
lead length, 3-21, D-2
optional reactor, D-3
shielded cable, D-1
Mounting dimensions, 3-3 to 3-7
E frame, 3-5
F frame, 3-6
G and H frames, 3-7
MOV surge protector, 2-1
P
PMI regulator, 2-2
Pre-charge assembly, 2-2
R
Rating codes, 1-2
Rectifier, 2-1
Related hardware and software, 1-6
Related publications, 1-3 to 1-6
Replacement parts, 4-7
Resolver & drive I/O board, 2-2
RFI filter, 3-24 to 3-25
S
Schematic diagrams, B-1 to B-8
150 to 250 HP drives @ 380/460V, B-5 to B-6
150 to 300 HP drives @ 575V, B-5 to B-6
20 to 30 HP drives @ 230V, B-2 to B-3
25 to 60 HP drives @ 575V, B-2 to B-3
250 to 650 HP drives, B-7
3 to 15 HP drives @ 230V and 460V, B-1
3 to 20 HP drives @ 575V, B-1
300 to 400 HP drives, B-8
40 to 60 HP drives @ 460V, B-2 to B-3
75 & 100 HP @ drives 230V, B-4
Shielded cable, 3-20 to 3-21
Snubber, 2-2
Standard features, 1-3
Starting the drive, 3-27
T
Technical specifications, A-1 to A-18
ambient conditions, A-1
current ratings by model number, A-4 to A-5
derating guidelines, A-8 to A-18
enclosure requirements, A-6 to A-7
ground fault trip threshold, A-3
input ratings, A-1
output ratings, A-2 to A-3
programmable carrier frequencies, A-2
Terminal block TB1, 3-11 to 3-16
B frame drives, 3-13
C and D frame drives, 3-14
E, F, and G frame drives, 3-15
H frame drives, 3-16
TB1 signals, 3-12
U
Unbalanced distribution system, 3-8
W
Warnings, 4-5 to 4-6
bad gain data (bit 8), 4-6
CCLK not synchronized (bit 14), 4-6
DC bus overvoltage (bit 0), 4-5
DC bus undervoltage (bit 1), 4-5
Flex I/O communication (bit 13), 4-6
ground current (bit 2), 4-5
overtemperature (bit 7), 4-6
PMI regulator communication (bit 15), 4-6