L-gage, Laser gauging sensor, L-gage beam dimensions (typical) – Banner L-GAGE LG10 Series User Manual
Page 4: Focal point, Xy beam dimensions, Page
RADIANT PO
WER 0.15 mW
8KHz 8-16% DUTY CYCLE
660 - 680 nm
COMPLIES
WITH 21 CFR
1040.10 AND EN60825-1:1994
DO
NO
T S
TAR
E IN
TO
BE
AM
CLA
SS
2 L
AS
ER
PR
OD
UC
T
LASER LIGHT
Avo
id e
xpo
sure
-
lase
r lig
ht e
mitte
d
from
his
ap
ertu
re
TEACH
SLOW
FAST
GN
AL
SPEED
A
D
X
Y
Beam Dimensions
RA
DIA
NT
P
OW
ER
0.1
5 m
W
8K
Hz 8
-16
% D
UT
Y C
YC
LE
660
- 6
80 n
m
CO
MP
LIE
S W
ITH
21
C
FR
104
0.1
0 A
ND
E
N60
825
-1:1
994
DO
NO
T S
TAR
E IN
TO
BE
AM
CLA
SS
2 L
AS
ER
PR
OD
UC
T
LASER LIGHT
Avoid e
xposure -
laser light emitted
from his aper
ture
TEACH
SLOW
FAST
POWER
OUTPUT
SIGNAL
SPEED
A
D
20.2 mm (0.80")
55.3 mm
(2.18")
45.5 mm
(1.79")
4.6 mm
(0.18")
68.3 mm
(2.69")
9.3 mm
(0.37")
82.3 mm
(3.24")
23.9 mm
(0.94")
19.1 mm
(0.75")
Emitted Light
Received Light
L-GAGE Laser Gauging Sensor Specifications (continued)
L-GAGE
™
Laser Gauging Sensor
page
4
Indicators
Construction
Housing: Zinc alloy die-cast, plated and painted finish
Cover plate: aluminum with painted finish
Lens: acrylic
Green Power ON LED: Indicates when power is ON, overloaded output and laser status.
Yellow Output LED: Indicates when discrete load output is conducting.
Red Signal LED: Indicates when target is within sensing range and the condition of the received light
signal.
Tri-color Red/Green/Yellow TEACH LED: Indicates sensor is ready for programming each limit (indicates
red for analog output, green for discrete, and yellow for simultaneous analog and discrete.)
Yellow Fast/Slow LEDs: Combination of 2 lights ON or OFF indicates one of 3 response speeds.
NOTE: See page 5 for more information on indicator behavior.
Environmental Rating
IP67, NEMA 4X
Vibration and
Mechanical Shock
Vibration: 60 Hz, 30 minutes, 3 axes
Shock: 30G for 11 milliseconds, half sine wave, 3 axes
Operating Conditions
Temperature: -10° to +50° C (+14° to 122° F)
Maximum relative humidity: 90% at 50° C, non-condensing
Application Notes
For comparison, white ceramic test surface has approximately 91% of the reflectivity of a white Kodak test
card with a matte finish. A dark gray ceramic test surface has approximately 11% of the reflectivity of a white
Kodak test card with a matte finish.
Figure 2. L-GAGE Laser Gauging Sensor and beam dimensions
Connections
2 m (6.5') or 9 m (30') 7-conductor shielded PVC-jacketed attached cable.
L-GAGE Beam Dimensions (typical)
Focal
Point
†
Distance
Beam
Width (X)
Beam
Height (Y)
53 mm
(2.1")
45 mm
0.3 mm
0.5 mm
60 mm
53 mm
0.3 mm
0.1 mm
0.5 mm
0.1 mm
70 mm
(2.8")
45 mm
0.6 mm
0.9 mm
53 mm
0.4 mm
0.6 mm
60 mm
0.3 mm
0.4 mm
† The Focal Point is the distance measured from
the lens (front of sensor) at which the diameter
of the laser image is smallest.