Brother BAS-311F-L - Manual (Page 69)

11. CHANGING SPECIAL FUNCTION AND USING THE MEMORY SWITCHES
BAS-311F-0, 311F-L, 326F-0
62
Memory switches (30 - 3F)
Turn the dial while pressing the STEP BACK switch to change the values.
Switch No.
Possible
setting range
Units
Initial
Value
Explanation
memo-30 1 - 999 X 10ms 10
Time until feed mechanism starts moving after work clamp has
lifted.
memo-31 1 - 4 - 1
Changes the feed speed.
1 (Fast) 4 (Slow)
memo-32 1 - 7 - 3
Changes the possible sewing speed for a given stitch length.
1 (Fast) 7 (Slow)
1 (2,700/3 mm), 2 (2,600/3 mm), 3 (2,500/3 mm),
4 (2,300/3 mm), 5 (2,000/3 mm), 6 (1,800/3 mm), 7 (1,200/3 mm)
Settings 1 and 2 are outside the warranty specification at the
time of shipment from the factory.)
memo-33 1 - 10 X 7.5 5
Changes the feed timing.
1 (Fast) 5 (standard) 10 (Slow)
memo-34 1 - 5 stitch 1 Number of low-speed stitches sewn at 400 rpm at sewing start.
memo-35 10 - 60 ms 40
Solenoid ON time changes (BAS-311F solenoid specifications
only).
10 (Quiet) 60 (High work clamp capacity)
memo-36 1 - 3 - 1
The solenoid ON time when the presser foot is raised changes.
(Standard) 1 3 (Upper limit)
memo-37 0 - 3 - 0
Automatically corrects the gear speed when reading 2DD disks.
0 : No automatic correction
1 : Read as BAS-311A data
2 : Read as BAS-326A data
3 : Read as BAS-341A, 342A data
ex. Read BAS-326A data by BAS-311F / Set memo-37=2
memo-38 1 - 20 X 100 ms 1
Changes the length of time from inserting the cassette until
automatic
starting when the eject device is being used and automatic starting has
been set (memo-03 and DIP switch A-7 are also both ON).
memo-39 0 - 11 - 0
Changes the reference point for enlargement and reduction using
the operation panel.
0 : Sensor home position
1 : Center of work clamp
2 : Upper-left corner of work clamp
3 : Lower-left corner of work clamp
4 : Upper-right corner of work clamp
5 : Lower-right corner of work clamp
6 : Sewing start point, 7 : Sewing end point
8 : Upper-left corner of sewing pattern
9 : Lower-left corner of sewing pattern
10 : Upper-right corner of sewing pattern
11 : Lower-right corner of sewing pattern
memo-3A 1 - 3 - 2
Changes the speed limit for the given sewing pitch when the
maximum speed remains constant.
1 : Speed limit is increased for the given sewing pitch and the
sewing speed for that pitch is increased.
2 : Standard
3 : Speed limit is decreased for the given sewing pitch and the
sewing speed for that pitch is decreased.
Note
If sewing slippage occurs in places where a large sewing pitch is
used, reduce the setting to 3.
Furthermore, sewing slippage may occur in some cases if setting
1 is used.
memo-3b - - 0 -
memo-3c - - 0 -
memo-3d - - 0 -
memo-3E - - 0 -
memo-3F - - 0