Tweco XT-300 Torch for OEM UC-300 - Manual (Page 31)

Manual 0-4829 Rev AN 8-33 TORCH DATA for Ultra-Cut
Shield
Cap
22-1127
ga in in psi Ball psi Ball psi (ipm) (in) (sec) (in)
10 0.07 40 55 120 35 120 280 0.200 0.2 0.065
3/16 0.07 40 55 120 35 120 190 0.200 0.2 0.070
1/4 0.07 40 55 120 35 120 150 0.200 0.3 0.078
3/8 0.07 40 55 120 35 120 95 0.250 0.4 0.085
1/2 0.07 40 55 120 40 120 68 0.300 0.6 0.097
5/8 0.07 40 55 120 40 120 55 0.350 0.8 0.100
3/4 0.07 40 55 120 40 120 25 0.125
mm bar Ball bar Ball bar (mm/min) (mm) (sec) (mm)
1.8 2.8 55 8.3 35 8.3 6120 5.1 0.2 1.7
1.8 2.8 55 8.3 35 8.3 4670 5.1 0.2 1.8
1.8 2.8 55 8.3 35 8.3 4030 5.1 0.3 1.9
1.8 2.8 55 8.3 35 8.3 3080 5.7 0.4 2.1
1.8 2.8 55 8.3 35 8.3 2300 6.5 0.4 2.2
1.8 2.8 55 8.3 40 8.3 1800 7.3 0.6 2.4
1.8 2.8 55 8.3 40 8.3 1370 8.5 0.7 2.5
1.8 2.8 55 8.3 40 8.3 640 3.2
10
12
15
20
4
5
6
8
(mm)
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later.
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
Kerf Width
@ Rec.
Speed Plasma (O
2
)
Shield
(Air)
Kerf Width
@ Rec.
Speed
Effective cut
Thickness
mm
M
in
imu
m
C
lea
ranc
e
Pre Flow
Pressure
(Air
2
)
Torch Working
Height
Plasma (O
2
)
Shield
(Air)
Pierce
Delay
Edge Start 3.8-6.35
Cut Flow Rates /
Pressures Travel
Speed
Effective cut
Thickness
.120-.250
Initial
Piercing
Height
M
in
imu
m
C
lea
ra
nc
e
Pre Flow
Pressure
(Air)
.070-.250
.090-.250
Travel
Speed
Edge Start Only
Pierce
Delay
Initial
Piercing
Height
22-1278
Cut Flow Rates /
Pressures
Shield Cup
22-1016
Shield Gas
Distributor
Plasma Gas
Distributor
Tip
22-1154 22-1041
Electrode
22-1172
Cartridge
22-1020
2.0-6.35
2.3-6.35
2.5-6.35
2.7-6.35
Mild Steel
100A Bevel Cut
O
2
Plasma / Air Shield
2.8-6.35
3.0-6.35
3.1-6.35
.120-.250
.150-.250
(in)
Torch Working
Height
.100-.250
.110-.250
Electrode Shield Cap Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB
8.02 Bevel Cutting Up To 100 Amp