John Deere stx38 - Manual (Page 16)

2 - 8
3/20/97
INCH FASTENER TORQUE VALUES SPECIFICATIONS AND INFORMATION
INCH FASTENER TORQUE VALUES
Grade 1 Grade 2 b Grade 5, 5.1 or 5.2 Grade 8 or 8.2
Lubricated a Dry a Lubricated a Dry a Lubricated a Dry a Lubricated a Dry a
SIZE N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft
1/4 3.7 2.8 4.7 3.5 6 4.5 7.5 5.5 9.5 7 12 9 13.5 10 17 12.5
5/16 7.7 5.5 10 7 12 9 15 11 20 15 25 18 28 21 35 26
3/8 14 10 17 13 22 16 27 20 35 26 44 33 50 36 63 46
7/16 22 16 28 20 35 26 44 32 55 41 70 52 80 58 100 75
1/2 33 25 42 31 53 39 67 50 85 63 110 80 120 90 150 115
9/16 48 36 60 45 75 56 95 70 125 90 155 115 175 130 225 160
5/8 67 50 85 62 105 78 135 100 170 125 215 160 215 160 300 225
3/4 120 87 150 110 190 140 240 175 300 225 375 280 425 310 550 400
7/8 190 140 240 175 190 140 240 175 490 360 625 450 700 500 875 650
1 290 210 360 270 290 210 360 270 725 540 925 675 1050 750 1300 975
1-1/8 470 300 510 375 470 300 510 375 900 675 1150 850 1450 1075 1850 1350
1-1/4 570 425 725 530 570 425 725 530 1300 950 1650 1200 2050 1500 2600 1950
1-3/8 750 550 950 700 750 550 950 700 1700 1250 2150 1550 2700 2000 3400 2550
1-1/2 1000 725 1250 925 990 725 1250 930 2250 1650 2850 2100 3600 2650 4550 3350
TS1162
1 or 2 b
2
5 5.1 5.2
5
8 8.2
8
No Marks
No Marks
SAE
Grade
and Nut
Markings
SAE
Grade
and Head
Markings
DO NOT use these hand torque values if a different
torque value or tightening procedure is given for a
specific application. Torque values listed are for
general use only and include a ±10% variance factor.
Check tightness of fasteners periodically. DO NOT use
air powered wrenches.
Shear bolts are designed to fail under predetermined
loads. Always replace shear bolts with identical grade.
Fasteners should be replaced with the same grade.
Make sure fastener threads are clean and that you
properly start thread engagement. This will prevent
them from failing when tightening.
When bolt and nut combination fasteners are used,
torque values should be applied to the NUT instead of
the bolt head.
Tighten toothed or serrated-type lock nuts to the full
torque value.
a “Lubricated” means coated with a lubricant such
as engine oil, or fasteners with phosphate and oil
coatings. “Dry” means plain or zinc plated (yellow
dichromate - Specification JDS117) without any
lubrication.
b “Grade 2” applies for hex cap screws (not hex
bolts) up to 152 mm (6-in.) long. “Grade 1”
applies for hex cap screws over 152 mm (6-in.)
long, and for all other types of bolts and screws
of any length.
Reference: JDS—G200.