John Deere stx38 - Manual (Page 176)

5 - 12
3/21/97
COMPONENT LOCATION POWER TRAIN
TRANSAXLE—DANA 5-SPEED
STX38 (SN 210001—301382)
STX46
1. Flange bearing
2. Shim (0.632x1.00x0.010–0.082 in.)
3. Spur gear (14 teeth)
4. Shift collar
5. Shift key (4 used)
6. Shifter Fork
7. Intermediate shifter/brake shaft
8. Woodruff key
9. Upper case housing
10. O-ring seal (2 used)
11. Screw (2 used) (1/4x0.734–20 in.)
12. Detent ball (2 used)
13. Detent spring (2 used)
14. Set screw (2 used) Flush Only
15. Shifter shaft rubber boot
16. Screw (14 used) (1/4x0.734–20 in.)
17. Retaining ring
18. Drive chain large sprocket /reverse gear (18 teeth)
19. Spacer (1.131x1.45x0.494 in.)
20. Intermediate shaft 1st gear (37 teeth)
21. Intermediate shaft 2nd gear (35 teeth)
22. Intermediate shaft 3rd gear (30 teeth)
23. Intermediate shaft 4th gear (27 teeth)
24. Intermediate shaft 5th gear
(SN 210001—270000 & Export)—22 teeth
(SN 270001— )—26 teeth
25. Spacer w/internal keys (1.133x1.50x0.375 in.)
26. Washer (0.640x0.137x0.061 in.)
27. Flange bearing
28. Square-cut rubber seal (open lip to inside)
29. Drive chain (24 pitches)
30. Retaining ring
31. Shim (0.632x1.00x0.010–0.082 in.)
32. Needle bearing (2 used)
33. Washer (2 used) (0.640x1.38x0.061 in.)
34. Input shaft
35. Bevel pinion gear (14 teeth)
36. Woodruff key
37. Retaining ring
38. Washer (0.632x1.00x0.026 in.)
39. Spacer (0.630x1.00x0.169 in.)
40. Washer (0.632x1.00x0.026 in.)
41. Idler gear (12 & 35 teeth)
42. Shim (0.632x1.00x0.010–0.082 in.)
43. Idler shaft
44. Flange bearing
45. Spacer (0.635x0.87x0.755 in.)
46. Drive chain drive sprocket (9 teeth)
47. Drive shaft bevel gear (42 teeth)
48. Shim (0.758x1.12–1.25x0.010–0.062 in.)
49. Drive shaft
50. Drive shaft 1st gear (12 teeth)
51. Drive shaft 2nd gear (15 teeth)
52. Drive shaft 3rd gear (20 teeth)
53. Drive shaft 4th gear (23 teeth)
54. Drive shaft 5th gear
(SN 210001—270000 & Export)—28 teeth
(SN 270001— )—24 teeth
55. Spacer (0.781x1.00x0.375 in.)
56. Washer (0.632x1.00x0.060 in.)
57. Flange bearing
58. Square-cut rubber ring
59. Left axle shaft
60. Washer (0.758x1.25x0.031 in.)
61. Washer (0.758x1.25x0.031 in.)
62. Differential bevel gear (15 teeth)
63. Retaining ring
64. Differential ring gear (32 teeth)
65. Differential bevel gear (15 teeth)
66. Retaining ring
67. Differential bevel gear (15 teeth)
68. Shim (0.758x1.12–1.25x0.010–0.062 in.)
69. Shim (0.758x1.12–1.25x0.010–0.062 in.)
70. Right axle shaft
71. Square-cut rubber ring
72. Differential cross shaft
73. Differential bevel gear (15 teeth)
74. Lower case housing
75. Thin friction puck
76. Brake disc (rotor)
77. Thick friction puck
78. Friction puck striker plate
79. Brake housing
80. Brake lever
81. Washer (0.321x1.00x0.055 in.)
82. Lever stop bracket
83. Cap screw (5/16x1.44–18 in.)
84. Lock nut (5/16–24 in.)
85. Lever Stop bushing (0.604x1.076x0.395 in.)
86. Actuator dowel pin (2 used)
87. Washer (0.321x1.00x0.055 in.)
88. Cap screw (5/16x2.25–18 in.)