Dell PowerVault 775N (Rackmount NAS Appliance) - Manual (Page 12)

E0212 VOLT PLANAR
REG System board is out of acceptable
voltage range; faulty or
improperly installed system board.
See " Troubleshooting Power Supplies " in "Troubleshooting
Your System."
E0276 CPU VRM n Specified microprocessor VRM is
faulty, unsupported, improperly
installed, or missing.
Ensure that supported VRMs of the same type are properly
installed. If the problem persists, replace the VRM (see
Figure 6-9 in "Installing System Options").
E0276 MISMATCH VRM
n
E0280 MISSING VRM
n
E0319 PCI OVER
CURRENT Faulty or improperly installed
expansion card.
See " Troubleshooting Expansion Cards " in "Troubleshooting
Your System."
E0412 RPM FAN n Specified cooling fan is faulty,
improperly installed, or missing.
See " Troubleshooting a Cooling Fan " in "Troubleshooting
Your System."
E0780 MISSING CPU
1 Microprocessor is not installed in
socket 1.
Install a microprocessor in socket 1 (see " Adding or
Replacing a Microprocessor " in "Installing System Options").
To identify microprocessor socket 1, see Figure A-3 .
E07F0 CPU IERR Faulty or improperly installed
microprocessor.
See " Troubleshooting a Microprocessor " in "Troubleshooting
Your System."
E07F1 TEMP CPU n
HOT Specified microprocessor is out of
acceptable temperature range and
has halted operation.
See " Troubleshooting System Cooling " in "Troubleshooting
Your System." If the problem persists, ensure that the
microprocessor heat sinks are properly installed (see
" Adding or Replacing a Microprocessor " in "Installing System
Options").
E07F4 POST CACHE Faulty or improperly installed
microprocessor.
See " Troubleshooting a Microprocessor " in "Troubleshooting
Your System."
E07F4 POST CPU REG
E07F4 POST CPU SMI SMI handler failed to initialize;
faulty system board.
See " Getting Help ."
E07FA TEMP CPU n
THERM Specified microprocessor is out of
acceptable temperature range and
is operating at a reduced speed,
or frequency.
See " Troubleshooting System Cooling " in "Troubleshooting
Your System." If the problem persists, ensure that the
microprocessor heat sinks are properly installed (see
" Adding or Replacing a Microprocessor " in "Installing System
Options").
E0876 POWER PS n No power available from the
specified power supply; specified
power supply is improperly
installed or faulty.
See " Troubleshooting Power Supplies " in "Troubleshooting
Your System."
E0880 INSUFFICIENT
PS Insufficient power is being
supplied to the system; power
supplies are improperly installed,
faulty, or missing.
See " Troubleshooting Power Supplies " in "Troubleshooting
Your System."
E0CB2 MEM SPARE
ROW Correctable errors threshold was
met in a memory bank: errors
were remapped to the spare row.
See " Troubleshooting System Memory " in "Troubleshooting
Your System."
E0CF1 MBE DIMM
Bank n Memory modules installed in the
specified bank are not the same
type and size; faulty memory
module(s).
Ensure that all banks contain memory modules of the same
type and size and that they are properly installed. If the
problem persists, see " Troubleshooting System Memory " in
"Troubleshooting Your System."
E0CF1 POST MEM 64K Parity failure in the first 64 KB of
main memory.
See " Troubleshooting System Memory " in "Troubleshooting
Your System."
E0CF1 POST NO
MEMORY Main-memory refresh verification
failure.
Ensure that all banks contain memory modules of the same
type and size and that they are properly installed. If the
problem persists, see " Troubleshooting System Memory " in
"Troubleshooting Your System."
E0CF5 LOG DISABLE
SBE Multiple single-bit errors on a
single memory module.
See " Troubleshooting System Memory " in "Troubleshooting
Your System."
E0D76 DRIVE FAIL Faulty or improperly installed hard
drive or RAID controller.
See " Troubleshooting Hard Drives " and " Troubleshooting a
RAID Controller Card " in "Troubleshooting Your System."