Two Brothers Racing Honda CB1000 User Manual

Cb1000r

Advertising
background image

12. Before you run the bike, clean off all fingerprints and dirt, as

any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and
enjoy. It is normal for some white smoke to appear the first
time you start the bike. This is packing/manufacturing oil
from inside the pipe burning off. Check for gaps or leaks.
If you find a leak, a little high temperature silicon sealant
should fix it. After 50 to 100 miles, recheck all fasteners for
tightness.

Parts List

IMPORTANT - PLEASE READ CAREFULLY

Installation

1. Make sure the bike is completely cool before starting the

installation. Make sure the bike is secure on the sidestand
or ideally a rear service stand.

2. Remove OEM Muffler assembly. Retain mounting bolt for

later use.

3. Remove the OEM rubber grommet and sleeve from OEM

muffler mounting location. This will not be reused.

4. Remove right side rear passenger foot rest assembly.

5. Install TBR muffler mounting backet behind OEM

passenger foot rest and re-install on motorcycle.

6. Attach TBR slip-tube to TBR muffler using the supplied

6x20mm bolts and lock washers. Leave loose for now.

7. Slide barrel clamp over slip-tube joint and rubber lined

muffler clamp over muffler assembly.

8. Install on motorcycle and attach using the OEM muffler

mounting bolt.

9. Align muffler and tighten the 4 X-ring bolts.

10. Tighten muffler clamp and barrel clamp at slip-tube joint.

11. Double check all your work.

Qty.

Description

Part Number

1

Muffler Canister

Varies

1

Slip-On Tube

005-28404S

1

Muffler Canister Clamp

Varies

1

HARDWARE KIT

005-284-3

2

X-Ring (half)

005-7-2-3

4

6x14mm Socket Head Cap Screw

005-SH614

4

6mm Split Lock Washer

005-WL6

1

Mounting Bracket

005-284-B

1

64mm Barrel Clamp

005-27-64MSH

1

5mm Long Handle Ball End Hex Key

005-9-18610

1

T20 Torx Short Hex Key

005-9-15820

1

TBR Sticker Kit

015-10212

2009-10 Honda

CB1000R

Slip-on Exhaust System with M-2 Canister
Part # 005-2840406V / 005-2840407V / 005-2840408V

Care & Cleaning

We recommend that this performance part be installed by a qualified motorcycle

technician. If you have any doubts as to your ability to install this performance

part, please consult with your local motorcycle dealer. Read all instructions first

before starting installation. Make sure the motorcycle and exhaust system are

completely cool before starting the installation. Also, make sure the bike is secure

on a centerstand or ideally a service lift during installation. Be sure to save all stock

components for possible use later.

**This product has not been tested with all available accessories and some

items may cause excessive heat. Excessive heat may cause damage to your

vehicle. Two Brothers Racing will not be responsible for damaged parts.

Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. For clean-
ing use a mild spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.

Stainless Header System: Polished stainless steel pipes will turn a light gold-
en hue after a few heat cycles, this is a normal characteristic of high quality
stainless steel.

Carbon Fiber Mufflers: Always make sure the fiberglass packing inside is in
good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the Carbon Fiber sleeve. TBR sells repack kits (TBR
part # 005-10038) that include new rivets and repack material as
well as a drill bit (#30), making it easy to do yourself. Also, NEV-
ER dyno test your bike with carbon fiber mufflers installed - the
intense heat and lack of cooling air can quickly cause the CF
material to burn. Two Brothers Racing does not provide a warranty for
burned carbon fiber.

Aluminum Mufflers: Use an aluminum or mag wheel polish such as Moth-
er’s to restore the bright finish to factory spec.

Advertising