KEYENCE FS-22X - Manual (Page 4)

4
Specifications are subject to change without notice.
KEYENCE CORPORATION
1-3-14, Higashi-Nakajima, Higashi-Yodogawa-ku,
Osaka, 533-8555, Japan
PHONE: +81-6-6379-2211
Copyright (c) 2010 KEYENCE CORPORATION. All rights reserved.
11224E 1070-1 96M11224
Printed in Japan
A7WW1-MAN-0069
9. Key Lock
The key lock function disables the operation of all keys.
Indicates that the
keys are locked.
Press the manual button for
three seconds while pressing
the mode button.
• Take the same step to unlock the keys.
10. Mode Settings before Shipping (Initialization)
The following factory settings are made before shipping.
EASY
FINE
OFF
Light-ON
Access mode
Power mode
Timer function
Output selection
* Returning to factory settings: Press the button for a minimum of
five seconds while pressing the button.
11. Hints On Correct Use
• To extend the cable length, use a cable with at least a 0.3 mm 2 cross-
section area. Limit the length of cable extension to no more than 100 m.
(To connect several units, contact Keyence for further information.)
• Do not wire the amplifier line along with power lines or high-tension
lines, or otherwise the sensor may malfunction or receive damage due
to noise.
• When using a commercially available switching regulator, ground the
frame ground terminal and ground terminal.
• Do not use the FS series outdoors, or in a place where extraneous light
can enter the light receiving surface directly.
• Due to the individual dispersion of characteristics and the difference in
fiber unit model, the maximum sensing distance or displayed value of
all the units are not the same.
• If the sensor is used in S-APC mode for a long time, the LED indicators
will be imposed with a heavy load. In that case, the sensor will be auto-
matically set to ACC mode where the current consumption of the sen-
sor for light emission will be constant, and “END APC” will be displayed.
The sensor can be continuously used in this case. Replace the sensor,
however, if highly precise detection is required.
12. Specifications
Model
Light source
Response time *1
Display shift function
Timer function
Control output
Supply voltage
Current consumption
Ambient
illumination
Ambient
temperature
Relative humidity
Vibration
Shock resistance
Housing material
Size
Weight
FS-V22 FS-V22G FS-V22R(P) FS-V20R FS-V22X
Red LED Greed LED 4-element red LED 4-element red LED Infrared (950 nm)
250µs (FINE)/500µs (TURBO)/1ms (SUPER TURBO)/
4ms (ULTRA TURBO)/500µs (HIGH RESOLUTION)/
50µs (HIGH SPEED)
Max. ±1999 (variable)
Timer OFF, OFF-delay timer, ON-delay timer, and one-shot timer
1 to 500 ms
NPN open collector output at 40 V (or PNP open collector output
at 30 V) with 20 mA max. and a residual voltage of 1 V max.
DC12-24V ±10% with a maximum ripple (peak to peak) of 10%, Class 2
Incandescent lamp: 20,000 lux max.
Sunlight: 30,000 lux max.
-10°C to 55°C (No freezing)*2
35% to 85% RH (No condensation)
10 to 55 Hz, 1.5-mm double amplitude,
each in X, Y, and Z directions for two hours
500 m/s
2 Three times each in X, Y, and Z directions
Unit and cover are both polycarbonate made
W 9 mm x L70 mm x H 30 mm
Approximately 45 g (including 2-m Cable)
Rating
Environment resistance
Mode
S-APC
mode OFF
580 mW
480 mW
430 mW
650 mW
530 mW
480 mW S-APC mode turned ON or when
the HIGH SPEED mode is selected.
720 mW
600 mW
550 mW
720 mW
600 mW
550 mW Normal
ECO half
ECO all
Normal
ECO half
ECO all
Model
Other than
R model
R model
*1. The FS-V20R has a response time between 210µs and 4.7 ms, de-
pending on the number of Units connected.
*2. Ambient operating temperature with amplifier expansion
1 to 2 units: -10°C to 55°C
3 to 10 units: -10°C to 50°C
11 to 16 units: -10°C to 45°C
13. List of Digital Display Items
Preset value/Current value display
Output selection (Dark ON)
Output selection (Light-ON)
Access mode selection (EASY)
Access mode selection (FULL)
Excess gain display
LED bar display
Hold display
Power mode selection (FINE)
Power mode selection (TURBO)
Power mode selection (SUPER TURBO)
Power mode selection (ULTRA TURBO)
Power mode selection (HIGH SPEED)
Power mode selection (HIGH RESOLUTION)
Timer function setting (Timer OFF)
Timer function setting (OFF-delay timer)
Timer function setting (ON-delay timer)
Timer function setting (One-shot timer)
S-APC mode setting (S-APC OFF)
S-APC mode setting (S-APC ON)
Edge detection mode (OFF)
Edge detection mode (Rising edge)
Edge detection mode (Falling edge)
ECO mode setting (ECO mode OFF)
ECO mode setting (ECO half)
ECO mode setting (ECO all)
Shift function setting (Shift OFF)
Shift function setting (Shift ON)
Key lock setting
Key unlock
Forecast maintenance warning (END APC)
KEYENCE products are strictly factory-inspected. However, in the event of a failure, contact
your nearest KEYENCE office with details of the failure.
1. WARRANTY PERIOD
The warranty period shall be for one year from the date that the product has been
delivered to the location specified by the purchaser.
2. WARRANTY SCOPE
(1) If a failure attributable to KEYENCE occurs within the abovementioned warranty period,
we will repair the product, free of charge. However, the following cases shall be
excluded from the warranty scope.
• Any failure resulting from improper conditions, improper environments, improper
handling, or improper usage other than described in the instruction manual, the
user’s manual, or the specifications specifically arranged between the purchaser and
KEYENCE.
• Any failure resulting from factors other than a defect of our product, such as the
purchaser’s equipment or the design of the purchaser’s software.
• Any failure resulting from modifications or repairs carried out by any person other
than KEYENCE staff.
• Any failure that can certainly be prevented when the expendable part(s) is
maintained or replaced correctly as described in the instruction manual, the user’s
manual, etc.
• Any failure caused by a factor that cannot be foreseen at a scientific/technical level
at the time when the product has been shipped from KEYENCE.
• Any disaster such as fire, earthquake, and flood, or any other external factor, such as
abnormal voltage, for which we are not liable.
(2) The warranty scope is limited to the extent set forth in item (1), and KEYENCE assumes
no liability for any purchaser’s secondary damage (damage of equipment, loss of
opportunities, loss of profits, etc.) or any other damage resulting from a failure of our
product.
3. PRODUCT APPLICABILITY
KEYENCE products are designed and manufactured as general-purpose products for
general industries.
Therefore, our products are not intended for the applications below and are not
applicable to them. If, however, the purchaser consults with us in advance regarding
the employment of our product, understands the specifications, ratings, and
performance of the product on their own responsibility, and takes necessary safety
measures, the product may be applied. In this case, the warranty scope shall be the
same as above.
• Facilities where the product may greatly affect human life or property, such as
nuclear power plants, aviation, railroads, ships, motor vehicles, or medical
equipment
• Public utilities such as electricity, gas, or water services
• Usage outdoors, under similar conditions or in similar environments
E 1040-1
WARRANTY