KEYENCE SR-750 Series - Manual

Copyright (c) 2013 KEYENCE CORPORATION. All rights reserved.
12481E 1033-1 96M12481 Printed in Japan
Information of the SR-750 Series Trial Unit
Thank you for using the SR-750 series trial unit, our 2D code reader.
Please make sure to include all the following items when you return the trial
unit.
„ Symbols
The following symbols alert you to important messages.
Be sure to read these messages carefully.
„ Package Contents
About a connector and a signal cable for the trial unit control cable.
„ RS-232C Connector
„ Control Cable (Crimping part of a pin terminal)
„ Control Cable (Crimping part of a Y terminal)
Please refer to the SR-750 Series Instruction Manual for the connection
methods of each cable.
There are following 2 methods employed for connecting power source to the
SR-750 Series.
• Connect the power supply wire of the control cable to a 24 VDC power
supply device.
• Connect to a PoE (Power over Ethernet) power supply device using the
Ethernet port.
Please use either one of the connection methods to supply power to the
SR-750 series.
It indicates a situation which, if not avoided, could result in
product damage as well as property damage.
F SR-750 Series Main Unit x 1
SR-750/751/750HA SR-752
F Installation Bracket x 1
F Installation Screw (M4) x 4 F Washer x 2
F Insulation Spacer x 2 F Port Cover (Power/Control Port,
Ethernet Port) x 1 each
F Trial Unit Control Cable (2 m) x 1 F NFPA79 Compliant Ethernet
Cable (2 m) × 1
F SR-750 Series Instruction
Manual
NOTICE
1 E SR-750-IM
Fixed Mount 2D Code Reader SR-750 Series
Instruction manual
Read this instruction manual before using the product in order to achieve maximum performance. Keep this instruction manual in a safe place after reading it so that it can be used at any time.
„ Symbols The following symbols alert you to important messages. Be sure to read these messages carefully.
Important It indicates cautions and limitations that must be followed during operation.
Point It indicates additional information on proper operation.
Reference It indicates tips for better understanding or useful information.
indicates the reference pages in this manual or the reference pages in separate manuals.
Safety Information for SR-750 Series
„ General Precautions
Safety precautions on Laser product
The SR-750 Series Fixed Mount 2D Code Reader uses a visible semiconductor laser, with a wavelength of 660 nm, as a Laser pointer for adjusting the reading position.
„ Laser Pointer Specifications
* The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice No.50.
Precautions on Proper Use
Precautions on Regulations and Standards
„ CE Marking Keyence Corporation has confirmed that this product complies with the essential requirements of the applicable EC Directive, based on the following specifications. Be sure to consider the following specifications when using this product in the Member State of European Union. z EMC Directive (2004/108/EC)
• Applicable standards EMI : EN61326-1, Class A EMS : EN61326-1 Remarks: These specifications do not give any guarantee that the end-product with this product incorporated complies with the essential requirements of EMC Directive. The manufacturer of the end-product is solely responsible for the compliance on the end-product itself according to EMC Directive. z Low-voltage Directive (2006/95/EC)
• Applicable Standard
EN60825-1, Class 1 Laser Product EN62471 „ FDA (CDRH) Regulations
This product complies with the following FDA (CDRH) regulations. • FDA(CDRH) Part 1040.10, Class 1 Laser Product The laser classification for FDA(CDRH) is implemented based on IEC60825- 1 in accordance with the requirements of Laser Notice No.50. „ FCC Regulations
This product complies with the following FCC EMI regulations. • FCC Part 15 Subpart B, Class A Digital Device
„ IC (Industry Canada) Regulations This product complies with the following IC EMI regulations. • ICES-003, Class A Digital Apparatus
It indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
It indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
It indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
It indicates a situation which, if not avoided, could result in product damage
as well as property damage.
• Do not use this product for the purpose to protect a human body or a part of human body. • This product is not intended for use as explosion-proof product. Do not use this product in a hazardous location and/or potentially explosive
atmosphere.
• Be sure to check that the SR-750 Series performs properly before starting the work or operation. • If the SR-750 Series malfunctions, take adequate safety precautions to prevent various types of damage. • Do not use the SR-750 Series in a manner not specified herein. It may result in fire, electric shock or malfunction. • It should be noted that functions and performances will not be guaranteed if the SR-750 Series is used in any way not specified or described in the
product specifications or it is modified.
• When the SR-750 Series is used in combination with other devices, functions and performance may be degraded, depending on the operating
conditions and environment.
Wavelength 660nm Output 60 PW Pulse duration 200 Ps
Laser class Class 1 Laser Product (IEC60825-1, FDA(CDRH) Part 1040.10*)
• Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. • Do not disassemble this product. The laser radiation emission from this product is not automatically stopped when it is disassembled. Precautions on Class 1 Laser Product
• Do not stare into the direct or specularly reflected beam.
96M12410
DANGER
WARNING
CAUTION
NOTICE
WARNING
CAUTION
NOTICE
WARNING
• Do not use a voltage other than that described in the specifications with the SR-750 Series. Doing so may damage to the unit. • The SR-750 Series employs 2 power connection methods, which are 24 V DC supply and supply from PoE power supply devices. When connecting
the SR-750 Series to the power source, be sure to use only one of these
methods. Using both power sources simultaneously may cause damage
to the units.
• Be sure to turn off the power to devices attached to the SR-750 Series when you plug in or unplug the cables.
Failure to do so may cause damage to the SR-750 Series.
• Do not disassemble or modify the SR-750 Series. Doing so may damage to the unit. • Place cables as far away as possible from high-voltage lines and power lines. Otherwise, electrical noise can be generated that may cause product
failure or malfunction. • The SR-750 Series is a precision instrument. Do not impact or drop the instrument. Pay particular attention when transporting or installing the
unit. • Do not hold the unit by its cable when carrying. The units may become damaged if the cables are disconnected or the units strike each other. • Do not allow water, oil, dust, or other foreign substances to stick to the scanner. This may cause read errors.
Use a soft, dry cloth to wipe any substance from the scanner. (Do not use
a cloth dipped in alcohol or other cleaning substance.)
NOTICE
Concerning the Trial Unit Control Cable
Pin
number Symbol
Details
Signal
direction
2 TXD Data send Output
3 RXD Data receive Input
5 SGND Signal GND -
Wire color Symbol Details
Green IN1 IN1 Input
Gray IN2 IN2 Input
White and
Blue
INCOM Input Common
Pink OUT1 OUT1 Output
Light Blue OUT2 OUT2 Output
White OUT3 OUT3 Output
Black OUTCOM
Output
Common
Wire color Symbol Details
Brown 24 V
+24 V Power
source
Blue 0 V
Power source
GND
Black Tube FG FG
Connecting the Power Source
Make sure to use only one of the connection methods for
power supply.
If power is supplied both from the control cable and PoE
power supply device at the
same time, the unit may be damaged.
5 4 3 2 1
9 8 7 6
D-sub9 Pin (female)
DTE Specification
(Terminal definition)
M2.6 Screw
1 mm
10 mm
6.6 mm
11 mm
4.3 mm
NOTICE
96M12481