KEYENCE MS-F07 - Manual

1 MS-E07/F07-IM_E
Compact Switching Power Supply
MS-E07/F07
Instruction Manual
Read this manual before using the product in order to achieve maximum
performance.
Keep this manual in a safe place after reading it so that it can be used at any time.
 Symbols
The following symbols alert you to important messages. Be sure to read these
messages carefully.
 CE Marking
Keyence Corporation has confirmed that this product complies with the essential
requirements of the applicable EC Directive, based on the following specifications.
Be sure to consider the following specifications when using this product in the
Member State of European Union.
 EMC Directive (2004/108/EC)
• Applicable Standard EMI: EN55011, Group1 Class A
EMS: EN61000-6-2
Remarks:
These specifications do not give any guarantee that the end-product with this
product incorporated complies with the essential requirements of EMC Directive.
The manufacturer of the end-product is solely responsible for the compliance on the
end-product itself according to EMC Directive.
 Low-Voltage Directive (2006/95/EC)
• Applicable Standard EN60950-1
• Overvoltage category II
• Use this product under pollution degree 2
• This product is an open type device. Therefore, it must be installed in an
enclosure with IP54 or higher. (Industrial control panel)
• Use this product under conditions in which the load factor is 70% or less
• Be sure to install the wiring to the AC input terminals and FG terminal inside the
industrial control panel.
 UL Certificate
This product is an UL/C-UL Recognied product.
• UL File No. E197232
• Category QQGQ2/QQGQ8
Be sure to consider the following specifications when using this product as an UL/
C-UL Recognized product.
• Overvoltage category II
• Use this product under pollution degree 2
• This product is an open type device. Therefore, it must be installed in an
enclosure with IP54 or higher. (Industrial control panel).
• Be sure to install the wiring to the AC input terminals and FG terminal inside the
industrial control panel.
 Surrounding area
For heat dissipation, leave the following space between this unit and
control console walls or other devices.
Intorduction
It indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
It indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
It indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
It indicates a situation which, if not avoided, could result in
product damage as well as property damage.
It indicates cautions and limitations that must be followed during
operation.
It indicates additional information on proper operation.
It indicates tips for better understanding or useful information.
Safety Information for MS Series
Do not use this product for the purpose to protect a human
body or a part of human body.
This product is not intended for use as explosion-proof
product. Do not use this product in a hazardous location and/
or potentially explosive atmosphere.
Do not perform any electrical wiring while electric current is
applied. Failure to follow this may result in an electric shock or
fire.
Be sure to connect the grounding cable. Failure to follow this
may result in an electric shock or fire.
Do not touch this unit within 1 minute after AC input is turned
off. Failure to follow this may result in an electric shock.
Do not modify or repair this unit. Failure to follow this may
result in an electric shock, accident, or product failure.
Do not touch any terminal of this unit while electric current is
applied.
Use the unit with the terminal cover installed to avoid an
electric shock.
When this unit is used in a system that may cause a serious
accident or damage if the unit fails, be sure to install a safety
device.
Pay attention to prevent foreign matter such as metal particles,
dust, paper, or wood chips from entering the inside of this
unit. Failure to follow this may result in a fire or product failure.
Do not touch any metallic part while electric current is applied
or immediately after input is shut off. Failure to follow this may
result in a burn due to a high temperature.
If a failure or abnormality occurs while this unit is in use,
immediately shut off AC input and stop operation of this unit.
Failure to follow this may result in a fire or accident.
DANGER
WARNING
CAUTION
NOTICE
Important
Point
Reference
WARNING
CAUTION
Check that the AC input rated voltage of this unit is equal to
the voltage of the AC power supply.
Do not connect the AC power supply to the DC output
terminals.
Do not disturb the convection of air near the vent of the
casing.
Precautions on Regulations and Standards
Part Names
Installation Method
NOTICE
DC output terminals
Connect the load cable
MS-E07: 5 VDC
MS-F07: 12 VDC
Output indicator
Illuminates when DC output (+V,
-V) is ON.
Output voltage adjustment trimmer
Adjusts output voltage within the
range of ±5%.
FG terminal
Connect the grounding cable.
AC input terminals
Connect the input cable (100 to
240 VAC)
Note: This terminal is N.C. (not connected) unless otherwise specified.
Do not use this terminal.
10 mm or more
10 mm or
more 10 mm
or more
10 mm or more
MS-E/F
Every direction: 10 mm min.
96M11797