Kenwood KR-V990D - Manual (Page 19)

MAnPn -QPT IID _
"iNPUf "■ MEÒT'Q-O^
"iv.............. OTliiu"“
VIDE01 POWE b Q
TV INPUT n ^
■" sound "’"
"vtùtfOi 'u.... ™
□SET „ nCANCEL
MACRO HI El
MACRO SET UP
INPUT nuinpru
uiiii-in pnwiRt I ^
■ ■ W ■ input ■ ■"’□■pUNC.T©- (2)f
"bOUNU ’u«"'
VIDE01 □
□SET ^ DCANCEL
MACRO Oil
MACRO SET UP
INPUT DViDEOI
....JV..................................................-7-^
:--"VlDE01 POWERlJSs
‘"Tv" INVui.uhUPiO'. Y ‘
....................................ТЖ а У"‘^'®_5(2)Ж
.......... :ÀNCEL
-VIDE01
I^ mai ’ n Шк1
0 Enter the commands for the receiver.
d)Set the receiver's input selector to the source you want to play. This setting also
turns on the receiver (when the MAIN POWER key set to the ON position.)
The INPUT changes as follows:
none — CD “► TAPE! A (deck A) or WID TAPE1B (deck B) or MD — LD
VIDE01 VIDE02 -► TV -► CABLE -► none
SelegtViPEQT
• If you connect a single cassette deck, select "TAPE1B" when selecting the TAPE 1 input.
•To playback from audio components, make system control connections to KENWOOD audio
components beforehand.
©Select the SOUND mode by referring to "Sound modes". -*l2il
The mode changes as follows:
STEREO PRO LOGIC -► AUTO — DOLBY 3 STEREO — DSP LOGIC
^ STEREO
Select PRO LQjaiil
O Enter the commands for your monitor TV.
0Set the timing for the monitor TV commands. Your monitor TV may not be able to
receive remote commands immediately after the POWER ON signal. This setting
lets you turn ON the monitor TV and program a delay before the next signal.
The timing changes as follows:
none (no POWER ON signal; sends remote command immediately)
-►Is (sends command 1 second after POWER ON) 5s (5 seconds after)
-► 10s (10 seconds after) -► none
Select 5s.
© Set the command necessary to switch your monitor TV input in order to view video
playback. First, determine how many times you have to press the input selector on
your monitor TV to reach the correct video input, then set that number (FUNC.1,2).
If you watch videos by choosing a TV channel instead of switching the input, set the
correct channel (TV1CH, TV2CH, TV3CH).
The setting changes as follows:
none (0 times) -► FUNC.1 (1 time) -► FUNC.2 (2 times) -► TV1CH -► TV2CH
-► TV3CH none
• If your TV switches to VIDEO when you press the input selector once:
■4 Select FUNC.1
O Enter the commands for your playback source (VCR).
© Set the timing for the command of the video components, such as a VCR. It is also
necessary to program a delay between the POWER ON and PLAY signals for your
playback source.
The timing changes as follows:
none (no POWER ON signal; sends remote command immediately)
-►Is (sends command 1 second after POWER ON) -► 5s (5 seconds after)
-► 10s (10 seconds after) -► none
Select 5s.
© Set the operation mode for the playback source. If the playback source is a TV (etc.),
use the remote's numeric (and ENTER) keys to select the channel.
Select PLAY.
O Select SET.
This completes the setup for MACR01.
O To enter another MACRO SET UP, repeat steps 0-4^.
O
Go back to the main menu.
O Press the GUI key on the remote to turn off the on-screen display.
KR-V93DD [En]
To use the MACRO PLAY
t
Ъ Ъ
o
Load the video (or audio) software.
• Remove video (or audio) software from all other connected components.
O Press MACR01 or MACROS when the receiver's MAIN POWER switch is set
to ON to carry out the operations set in the respective macro.
• If you set the macro to turn ON the power to your video components in steps OTl) and
©-d), be sure those components are turned OFF when you press the MACRO key. If they
are turned ON when you press the MACRO key, they will be turned OFF.
This compietes the system setup. If you add a new component or change a component, be sure to return to SYSTEM SET UP
and correct the settings that apply to the component that was added or changed.