Kenwood KR-V990D - Manual (Page 9)

Connecting the system control
(~Co\
l^cor
Ш"
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of
convenient system control operations.
lere are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown
'elow.
[XSB] Mode : lets you combine DC2, CXS], and CX?] terminals
[5L1E] Mode : for I5L1E] terminals only
This unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, follow
the instructions in "SWITCHING FROM ISL16] TO [XS8]" below.
EXAMPLE: [XS8] mode connections
The underlined portion represents the setting of the system control mode.
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system control mode.
[SL16] rXS81
[SL16]
[SL16]
rSLieUXSI rXSSHXRl
[SL16] [Ш [XS8]
[XSl
SYSTEM
CONTROL
cord
FSLiei [XS81
[SL161
[SL16]
[SL161 [XS] [XS8] [XR]
rSLISI [XS] [XS8]
[XS]
SYSTEM
CONTROL
cord
Record player
> Some CD players and cassette decks are not compatible with the ISL16] system control mode. Be sure to use the [XS8] system control mode when
making system connections with equipment that is not [SL16] compatible.
► Some LD players and MD players are not system control compatible. You cannot make system control connections to this kind of equipment.
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If your
equipment consists of this kind of combination, please do not connect any system control cords. Even without
system control cords, normal operations can be carried out without affecting performance.
2. Do not connect systenn control cords to any components other than those specified by KENWOOD. It may
cause a malfunction and damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the system control terminals.
SYSTEM CONTROL OPERATIONS
Remote Control
Lets you operate this unit with the system remote supplied with the
receiver.
Automatic Operation (except [XR] equipment)
When you start playback from a source component, the inputselector
on this unit switches to that component automatically.
(Except for TAPE 2.)
Synchronized Recording (except [XR] equipment)
Lets you synchronize recording with the start of playback when
recording from CD, MD, LD, or analog discs.
On-Screen system operation ([SL16] only]
This unit can display the current status of the component you wish to
operate on the screen of a monitor television and let you operate that
component with on-screen operations.
SWITCHING FR0M[SL16] TOPCSS] -w
You can easily change the system control mode with the following
operation. Do this operation after completing all connections.
Switching to [XS8] : Hold down the BAND key and switch the
MAIN POWER key from OFF to ON.
Switching backtoISLI 6): Hold down the AUTO key and switch the
MAIN POWER key from OFF to ON.
•This operation will not affect items stored in the memory.
You can also change the mode using the On Screen Display.
The system control mode will revert to [SLI6] if the unit
is not turned on for three consecutive days. If you would
>iDI like to make the unit completely (and permanently) [XL8]
compatible, please consult your dealer.
^WITCHING THE TAPE 11NPUT TO MD ([SL16] only)
^^f you set the SYSTEM CONTROLto [SLI 6] modeand connectan MD ^
recorder, be sure to switch the receiver's TAPE 1 input to MD.
To switch the input, follow the steps shown below. (The input can
also be switched through an on-screen operation.)
0 Set the input to TAPE 1
0 Hold down the AUTO key on the receiver for more than 2 seconds.
Repeat to return to the original input setting (TAPE 1).