Document Outline

• Package Contents
  • What’s in the box
  • Product Description
  • Product Features
  • Product Specifications
• Hardware Description
  • Physical Dimensions
    • GE-DSH-82
    • GE-DSH-82-PoE
  • Front / Rear Panel
  • Top View
  • LED Indicators
    • GE-DSH-82 LED Indicators
    • GE-DSH-73 LED Indicators
    • GE-DSH-82-PoE LED Indicators
• Installing the Switch
  • Installation Steps
  • DIN-Rail Mounting
  • Wall Mount Plate Mounting
  • Wiring the Power Inputs
  • Wiring the Fault Alarm Contact
  • Wiring the Digital Inputs / Outputs (GE-DSH-73)
  • Installing the SFP transceiver
    • Approved GE Security SFP Transceivers
  • Factory Redundant Ring Application
  • Transportation Networking and Public Wireless Service
  • X-Ring Application
  • Coupling Ring Application
  • Dual Homing Application
  • Connecting to the Console Port
    • DB9/ RJ-45 Connector Pinouts
  • Login in the Console Interface
  • CLI Management
    • CLI commands and descriptions
• About Web-based Management
• Requirements
• Logging on the Switch
• System
  • System Information
  • IP Configuration
  • DHCP Server
    • System configuration
    • Client Entries
    • Port and IP Bindings
  • TFTP
    • Update Firmware
    • Restore Configuration
    • Backup Configuration
  • System Event Log
    • Syslog Configuration
    • System Event Log-SMTP Configuration
    • System Event Log-Event Configuration
  • Fault Relay Alarm
  • SNTP Configuration
  • IP Security
  • User Authentication
• Port Management
  • Port Statistics
  • Port Control
  • Port Trunk
  • Aggregator setting
    • Aggregator Information
    • State Activity
  • Port Mirroring
  • Rate Limiting
• Protocol
  • VLAN Configuration
    • VLAN Overview
    • VLAN Configuration
    • Port-based VLAN
    • 802.1Q VLAN
    • Understanding the nomenclature of the Switch
  • Rapid Spanning Tree Protocol
    • Theory
    • Bridge Protocol Data Units
    • Creating a Stable STP Topology
    • STP Port States
  • RSTP Parameters
    • RSTP Operation Levels
    • Default Spanning-Tree Configuration
    • User-Changeable STA Parameters
  • Illustration of STP
  • RSTP System Configuration
    • Port Configuration
  • SNMP Configuration
    • System Configuration
    • Trap Configuration
    • SNMPV3 Configuration
  • QoS Configuration
    • QoS Policy and Priority Type
    • Port-based Priority
    • COS Configuration
    • TOS Configuration
  • IGMP Snooping
    • Theory
    • About the Internet Group Management Protocol (IGMP) Snooping
    • IGMP Versions 1 and 2
  • IGMP Configuration
  • X-Ring
    • X-Ring Application
    • Dual Homing Application
    • X-Ring Configuration
• Security
  • Security-802.1X/Radius Configuration
    • Understanding IEEE 802.1X Port-Based Authentication
    • System Configuration
    • Port Configuration
    • Port Configuration
  • MAC Address Table
    • Static MAC Address
    • MAC Filtering
    • All MAC Addresses
    • Multicast Filtering
• Digital Input/Output (GE-DSH-73)
  • Digital Input
    • Digital Output
• Power Over Ethernet (GE-DSH-82-PoE)
  • Power over Ethernet Powered Device
  • Power Management
• Factory Default
• Save Configuration
• System Reboot
• System Commands Set
• Port Commands Set
• Trunk Commands Set
• VLAN Commands Set
• Spanning Tree Commands Set
• QOS Commands Set
• IGMP Commands Set
• MAC / Filter Table Commands Set
• SNMP Commands Set
• Port Mirroring Commands Set
• 802.1x Commands Set
• TFTP Commands Set
• SystemLog, SMTP and Event Commands Set
• SNTP Commands Set
• X-ring Commands Set
• PoE Command Set
• Address Table
  • Learning
  • Forwarding & Filtering
  • Store-and-Forward
  • Auto-Negotiation
• What is PoE?
  • PoE System Architecture
  • How Power is Transferred Through the Cable
    • When to install PoE?
  • The PoE Provision Process
  • Stages of powering up a PoE link
  • Line Detection
  • Classification
  • Start-up
  • Operation
  • Power Overloads
  • Power Disconnection Scenarios
  • DC Disconnect
  • AC Disconnect
• Switch's RJ-45 Pin Assignments
• 10/100Mbps, 10/100Base-TX