Flowserve Durco Mark 3 ISO Frame Mounted User Manual
Page 3
DURCO MARK 3 ISO FRAME MOUNTED ENGLISH 85392719 12-14
Page 3 of 52
flowserve.com
INDEX
Page
Additional sources (10.3) ......................................... 49
Alignment of shafting (see 4.3, 4.5 and 4.8)
Assembly (6.10) ....................................................... 31
ATEX marking (1.6.4.2) ............................................. 7
Bearing sizes and capacities (5.2.2) ....................... 21
CE marking and approvals (1.2) ................................ 4
Certification (9) ........................................................ 49
Change notes (10.2) ................................................ 49
Clearances, impeller (6.7) ....................................... 28
Commissioning and operation (5) ........................... 20
Compliance, ATEX (1.6.4.1) ...................................... 6
Configurations (3.1) ................................................. 11
Copyright (1.4) ........................................................... 4
Design of major parts (3.3) ...................................... 12
Direction of rotation (5.4) ......................................... 22
Disassembly (6.8) .................................................... 29
Disclaimer (1.3).......................................................... 4
Dismantling (6.8, Disassembly) ............................... 29
Drawings (8) ........................................................... 38
Duty conditions (1.5) .................................................. 4
Electrical connections (0) ........................................ 20
End of product life (2.5) ........................................... 11
Examination of parts (6.9) ....................................... 30
Fastener torques (6.6) ............................................. 28
Faults; causes and remedies (7) ............................. 36
Foundation (4.3) ...................................................... 13
General arrangement drawing (8.5) ........................ 49
General assembly drawings (8) ............................... 38
Grouting (4.4)........................................................... 14
Guarding (5.5).......................................................... 22
Handling (2.2) .......................................................... 10
Hydraulic, mechanical and electrical duty (5.10) ..... 25
Impeller clearance (see 5.3 and 6.7)
Inspection (6.2.1 and 6.2.2) ..................................... 26
Installation (4) .......................................................... 13
Lifting (2.3) ............................................................... 10
Location (4.1) ........................................................... 13
Lubrication (see 5.1.1, 5.2 and 6.2.3)
Lubrication schedule (see 6.2.3)
Maintenance (6) ....................................................... 25
Maintenance schedule (6.2) .................................... 26
Name nomenclature (3.2) ........................................ 11
Nameplate (1.7.1) ...................................................... 9
Nozzle loads (4.6.4) ................................................. 16
Operating limits (3.4.1) ............................................ 12
Ordering spare parts (6.3.1) .................................... 27
Part assemblies (4.2) ............................................... 13
Parts interchangeability (8.4) ................................... 45
Parts lists (8) ............................................................ 38
Performance (3.4) .................................................... 12
Piping (4.6) .............................................................. 15
Pre-commissioning (5.1) .......................................... 20
Priming and auxiliary supplies (5.6) ........................ 22
Page
Protection systems (4.9) ..........................................20
Reassembly (6.10, Assembly) .................................31
Receipt and unpacking (2.1) ....................................10
Recommended fill quantities (see 5.2.2) ..................21
Recommended grease lubricants (5.2.3) .................22
Recommended oil lubricants (5.2.1) ........................21
Recommended spares (6.4) .....................................27
Recycling (2.5) .........................................................11
Replacement parts (6.3 and 6.4) ..............................27
Running the pump (5.8) ...........................................23
Safety action (1.6.3) ................................................... 5
Safety labels (1.7.2) ................................................... 9
Safety markings (1.6.1) .............................................. 5
Safety, protection systems (see 1.6 and 4.9)
Sealing arrangements (6.11) ....................................33
Sectional drawings (8) ..............................................38
Setting impeller clearance (6.7) ...............................28
Sound pressure level (1.9, Noise level) ..................... 9
Sources, additional information (10.3) .....................49
Spare parts (6.3) ......................................................27
Specific machine performance (1.8) .......................... 9
Starting the pump (5.7).............................................23
Stop/start frequency (5.8.5) ......................................24
Stopping and shutdown (5.9) ...................................24
Storage, pump (2.4) .................................................11
Storage, spare parts (6.3.2) .....................................27
Supplementary manuals or information sources ......49
Supplementary User Instructions (10.1)...................49
Thermal expansion (4.5.1) .......................................14
Tools required (6.5) ..................................................27
Torques for fasteners (6.6) .......................................28
Trouble-shooting (see 7) ..........................................36
Vibration (5.8.4) ........................................................24