Gasboy 215A - Manual

032113 Rev. 8196 Page 1
MODEL 215A VAPOR RECOVERY KIT INSTALLATION INSTRUCTIONS
This instruction sheet covers the installation of the Model 215A Balanced System Vapor Recovery Kit (Gasboy P/N
032112). You should have received the following:
Item Qty. P/N Description
1 1 032671 Clamp and Reel Assy.
2 1 063816 Support Post
3 1 017930 Cap plug 1-1/2”
4 4 051955 Screw 5/16-18 x 2
5 4 068080 Washer 5/16
6 4 068875 Washer, Lock 5/16
7 1 056924 Spacer
8 1 013250 Bolt 5/16 (Anchor)
9 1 047219 Plug Button
10 1 038605 Nut 5/16-18 Hex Keps
11 1 064560 ¾” Swivel
Item Qty. P/N Description
12 1 038502 Nozzle-Emco VR
13 1 030301 Hose GY 7.5’
14 1 066817 Splitter, Emco
15 1 030407 Hose ¾” HW 1.5’
16 1 017270 ¾” to 1” Bushing
17 1 044007 Breakaway
18 1 030303 Hose GY 4.5’
19 1 003336 Boot-Nozzle
20 1 003719 Hook-Nozzle
21 4 053639 Screw 8-32 x 5/8
N/A 1 032113 Instruction Sheet
N/A 1 035282 Warning Sheet
Always use a UL-classified gas- and oil-resistant pipe compound on all male pipe threads when assembling these
components. All references to pipe compound in these instructions imply UL-classified pipe compound. In addition
to the standard tools and supplies required for dispenser installations, you will also need the following:
•
1.30” diameter sheet metal drill bit (or similar hole punching device)
•
.34” diameter sheet metal drill bit
1. Read all instructions before beginning. A separate instruction sheet is packed with the EMCO Wheaton splitter
manifold, which is required for mounting this component. Also, read and follow all precautions regarding
remote dispensers and pumps on the Warnings and Safeguards sheet, 035282, included in this kit.
2. Turn off power to the dispenser at the breaker and activate emergency shutoff valve.
3. Before removing dispenser from the island, determine the splitter manifold location as instructed in the EMCO
Wheaton instructions.
4. Remove dispenser from island before performing any work which may produce sparks (e.g. drilling, use of
power tools, etc.).
5. With the dispenser at a safe distance from the island, drill the splitter mounting holes per the EMCO Wheaton
instructions.
6. Reinstall the dispenser on the island, and mount the splitter per the EMCO Wheaton instructions.
Assemble Product Jumper Hose
7. Assemble ¾” x 1” bushing (017270) to dispenser outlet. Assemble ¾” swivel (064560) to one end of ¾” jumper
hose (030407). Assemble fixed end of jumper hose to bushing on dispenser outlet, and the swivel end at the
splitter port labeled FUEL.
Mounting Hose Retriever
8. Assemble clamp and reel assembly (item 1) to support post (item 2) with hardware items 4, 5, and 6.
9. Install reel and support post assembly to side of dispensing unit with items 4, 5, 6, 7, and 10 and leave loose.
Item 7 mounts between post and side panel.
10. Making sure that support post is plumb, mark and drill a 5/8” dia. X 1-3/4” deep hole in island. Install anchor
bolt (item 8) into island surface. Install items 4, 5, and 6.
11. Tighten all hardware from Step 9. Plug hole in support post with item 9.