Marantz SR6001 - Manual (Page 54)

51
ENGLISH
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR6001 is sent to
the record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD/CDR OUT and VCR OUT in the record mode.
To record the input source signal you are currently
watching or listening to
- TUNING PRESET - + +
REMOTE CONTROLLER RC5001SR
AMP AUX2
BASS TREBLE
AUDIO ANGLE SUB TITLE DISC+
CH-SEL V-OFF ATT.
AUX1
MD MD CDR CDR CD CD
DVD DVD VCR VCR
TUNER TUNER
DSS DSS TV TV
TAPE
1.
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
MENU
PURE DIRECT HT-EQ
7.1CH INPUT
MODE AUTO MULTI
PURE DIRECT
SURROUND SPEAKE MULTI
DSD
POWER ON/STANDBY
DISP MULTI AUTO TUNED SLEEP SURR DIRECT AUTO
1.
1. Select the input source to record by turning the
INPUT FUNCTION SELECTOR knob on the
front panel or simply press the input selector
buttons on the remote.
The input source is now selected and you may
watch or listen to it as desired.
2. The currently selected input source signal is
output to the TAPE OUT, CD/CDR OUT and
VCR OUT outputs for recording.
3. Start recording to the recording component as
desired.
SPEAKER A/B
DIGITAL VIDEO S-VIDEO AUX 1 INPUT
VOLUME
DOWN
MultEQ ENTER MENU
7.1CH INPUT
MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
SPEAKER MULTI
L C R SL S SR LFE DIGITAL SURROUND V-OFF ULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
CAT
P.SCAN
CAT
7 8 9
0 +10 +10
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
INFO
CH/
M-SPKR
MUTE VOLUME
7.1CH IN
STEREO NIGHT M-CH ST
MEMO CL
A/D A/D
SR6001 has speaker system - A and speaker
system- B for front L/R channels.
You can select these systems by pressing
SPEAKERS A/B button on the front panel or SPKR
A/B on the remote.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
TAPE
REMOTE CONTROLLER RC5001SR
MD CDR CD
DVD
AUX2
VCR
TUNER
DSS TV
AUX1 AMP AMP
CAT
P.SCAN
CAT
4 5 6
7 8 9
0 +10 +10
HT-EQ
MULTI/
SPKR A/B CH/
M-SPKR
MUTE VOLUME
7.1CH IN
STEREO NIGHT M-CH ST
MEMO CL
A/D A/D
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button fi rst to enter the AMP mode
then press the A/D button.
When this button is pressed, the input mode is
switched in the following sequence.
Auto → HDMI → Digital → Analog → Auto
Auto mode:
The types of signals being input to the digital and
analog input jacks for the selected input source are
detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
HDMI mode:
HDMI mode can be selected only when an HDMI
input has been assigned as an input source.
When “HDMI AUDIO” under PREFERENCE of the
SETUP MENU is set to “THROUGH”, the HDMI
mode cannot be selected.
Digital mode:
The input signal is fi xed to an assigned digital input
terminal.
Analog mode:
The analog input jacks are selected.
This selection is temporary and will not be stored in
memory.
To store changes to the input mode, select “1. INPUT
SETUP” from the MAIN MENU. (See page 29)
DISPLAY MODE
P.SCAN
T.MODE
1 2 3
4 5 6
7 8 9
SEND
INPUT
EX/ES VIRTUAL CS
dts
P.DIRECT
l/
OFF ON SET
STEREO NIGHT M-CH ST
AUTO
SURROUND SLEEP
LEARN
LIP SYNC/
SOURCE
DISPLAY DISPLAY
BAND
PHONES
AV SURROUND RECEIVER SR6001
MultEQ ENTER MENU
PURE DIRECT HT-EQ
7.1CH INPUT
MODE AUTO MULTI T-MODE MEMORY
DISPLAY
EXIT
S
BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
L C R SL S SR LFE
DIGITAL SURROUND V-OFF DISP MULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
You can select the display mode for the front display
of the SR6001.
To select this mode, press the DISPLAY on the
remote control or the front panel.
When this button is pressed, the display mode is
switched in the following sequence.
Input Mode → Surround Mode → Auto display OFF
→ Display OFF → Normal Mode → Input Mode
Normal Mode:
Displays the selected input function. If the function
has been renamed using the Function Rename
feature (see page 30), the renamed name appears
on the display.
Input Mode:
Displays the input mode set via the Function Input
Setup feature (see page 29).
Surround Mode:
Displays the status of the selected surround
mode.
Auto Display Off mode:
The display is off. But, if you make a change to
the unit such as the input or surround mode, the
display will show that change, then go back to off
after about 3 seconds. When changing the volume,
it is not displayed.
Display Off mode:
The display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition.
SR6001U DFU_1_ENG 3_4.indd 51 SR6001U DFU_1_ENG 3_4.indd 51 06.12.21 4:15:41 PM 06.12.21 4:15:41 PM