Marantz SR6001 - Manual (Page 66)

63
ENGLISH
HDMI
SYMPTOM CAUSE REMEDY
The display does not
appear over an HDMI
connection. The connected monitor or projector
does not support HDCP.
The HDMI input of on the TV is
not on. Set HDMI input so that it turns on, as
explained in the TV's instruction manual.
The HDMI output on the source
component (DVD, Set Top Box,
etc.) is not on. Set HDMI output so that it turns on, as
explained in the source component's
instruction manual.
The HDMI mode is not correctly
set on the SR6001. Set HDMI input on the FUNC INPUT
SETUP menu as explained on page 29.
The HDMI output video resolution
of the source component (DVD,
Set Top Box, etc.) does not match
the TV specifi cations. Set the resolution so that it matches, as
explained in the instruction manuals of both
components.
The device is connected with a
non-standard HDMI cable. A 5 m or shorter cable is recommended to
ensure stable operation and prevent image
quality deterioration.
Power to the SR6001 is off.
(When the SR6001 is on standby,
HDMI connections cannot be
turned on.) Turn on the power to the SR6001.
T h e c o n n e c t i o n b e t w e e n
HDMI components was not
authenticated. Shut off and then turn the power back on to
the SR6001, TV and source component.
Time is needed for the
d i s p l ay o f a n H D M I
connection to appear. T h e c o n n e c t i o n i s b e i n g
authenticated between the HDMI
devices. There is nothing wrong with the system.
Some HDMI devices require time for
authentication.
Au d i o i s n o t p l aye d
b a ck ove r a n H D M I
connection. The HDMI audio output of the
source component (DVD, Set Top
Box, etc.) is not on. Set the HDMI audio output so that it turns
on, as explained in the source component's
instruction manual.
The signal format of the source
component (DVD, Set Top Box,
etc.) is not supported by the
SR6001. Set the HDMI audio output so that it can
connect to the SR6001, as explained in the
source component's instruction manual.
The SR6001 is set to the HDMI
audio “THROUGH” mode. In the “THROUGH” mode, sound is not
produced from the SR6001. Set it to
“ENABLE”. (see page 40)
DVD-Audio is not played
b a ck ove r a n H D M I
connection. The DVD player does not support
CPPM, therefore it cannot output
HDMI audio. • Use a DVD-Audio player that supports
CPPM.
• Turn on PCM downsampling on the DVD
player.
• Use an analog connection.
TROUBLESHOOTING
If a problem should arise, fi rst check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there
may be a malfunction. Disconnect the power immediately and contact your store of purchase.
SYMPTOM CAUSE REMEDY
“ANTENNA” is displayed. XM terminal and the XM Mini-Tuner and
Home Dock is not properly connected. Check that the connection are correct.
“NO SIGNAL” is displayed. The signal cannot be received. Reposition your XM Mini-Tuner and Home
Dock.
Receiving only XM channels 0 and 1. The XM Tuner is not activated. Contact XM Radio.
SR6001U DFU_1_ENG 4_4.indd 63 SR6001U DFU_1_ENG 4_4.indd 63 06.12.21 4:16:11 PM 06.12.21 4:16:11 PM