Document Outline

• CONTENT
• 1. Brief Introduction
  • Chapter Structure
  • How to Use the Manual
  • Term and Definitions
  • System Overview
  • Application Questions
• 2. Hardware Orientation
  • In This Chapter
  • VSP 9516S Back Panel
    • CONT Interface
      • 2: Dial Switch
      • 3: 10/100M UDP Interface
      • 4: USB Interface
      • 5: RS232 Interface
    • INPUT Interface
      • 16~25: Audio Input
      • 1: 3G-SDI Input
      • 26: Displayport Input
      • 30: S-Video DIN 4
      • 31: DVI Input
      • 32~34: YPbPr Input
      • 35: VGA Input
    • OUTPUT
      • 6.7.11.12: Gigabit Copper Port
      • 9.14: USB Control Port of Sending Card
      • 8.13: Audio Input of Sending Card
      • 10.15: DVI Input Port of Sending Card
      • 36: AUDIO Output
      • 37: DVI Output
      • 38: DVI +VGA DVI Output
    • Switch and Power
      • 39.40: Power Interface and Switch
  • VSP 9516S Front Panel
    • OLED Panel
    • LED Sending Card Indicator
    • Menu Buttons
• 3. Hardware Installation
  • In This Chapter
  • Safety Precautions
  • Unpacking and Inspection
  • Site Preparation
• 4. Menu Orientation
  • In This Chapter
  • MENU
    • INPUT
    • OUTPUT
    • TRANSITION
    • AUDIO
    • SPLIT
    • DISPLAY CONNECTION
    • SAVE SETUP
    • SYSTEM
    • LANGUAGE
    • FACTORY RESET
• 5. Communication Software Guideline
  • In This Chapter
  • Software Installation
  • Software Operation
    • Connection
    • Use
      • File Toolbar
      • Communication Toolbar
      • Device Toolbar
      • Schedule Toolbar
      • Output Resolution Toolbar
      • Images Display Mode Toolbar
      • Layout Toolbar
      • Aspect Ratio Toolbar
      • Signal Input Toolbar
      • Screen Parameter Toolbar
      • Image Toolbar
      • Display Toolbar
      • Output Image Setup Toolbar
      • LED Screen Toolbar
      • Images Display Toolbar
      • User Mode Toolbar
      • Log Toolbar
      • Information Toolbar
      • [Video Processor] Options
      • [Help] Options
  • How to Connect Windows Control Program by LAN Interface
  • How to Connect Windows Control Program by RS232 Interface
  • How to Connect Windows Control Program by USB Interface
• 6. System Setup and Operations
  • In This Chapter
  • Interface and Input Signal Option
  • How to Change the Language
  • How to Do Customized Output Resolution
  • How to Realize Single Image Switching
  • How to Set up the PIP
  • How to Set up the Size and Position of the Single Image
  • How to Realize the Screen Size Setting
  • How to Realize the Text Overlay Setting
  • How to Realize the Freeze and Live Image Switching
  • How to Set up the Volume
  • How to Realize LED Display Connection
  • How to Use Black Out
  • How to Save the Parameter
  • How to Load the Saved Parameter
• 7. Common Questions and Solutions
  • In This Chapter
  • No Output in LED Display
    • Confirm If There is Any Input Signal
    • Confirm If Signal Output
  • Flash Point in LED Display Output
    • Confirm If Monitor Output is Normal
  • LED Display Only Displays Part of the Image
    • Signal Needs to Scale
  • No Display in the Second Half Part of LED Display
    • Resolution is Insufficient
  • Left Screen Appears Two Black Sides
    • Adjust DE Deviation
  • All Key Lights Light on Simultaneously
    • Check If Dial Switch is Normal
  • Aliasstep or Shake When Input SDI Signal
  • Spottted Image or Freeze When Switch CV Signal
    • Normal Phenomenon
  • If DP Port Can Connect DVI or HDMI Signal
    • DP Port Can Only Connect DP Signal
• A. Specification
• B. Contact Information
• C. Software Upgrade
  • IP Software Download Instruction
  • Firmware Upgrade
  • How to Install the SDI Optional Module