Teac HS-4000 Addendum V1.22 - Manual (Page 10)

X
HS-4000
10
TASCAM HS-4000
Necessary setting for VNC connections 0
The following settings are necessary for connecting to this unit using a
VNC viewer application.
IP address: This unit’s IP address is shown in the
IP Address field of
the REMOTE SETUP screen ETHERNET
page.
Password: HS-4000 (default, case sensitive)
This setting can be changed by using the Password
Change
button on the
REMOTE SETUP
screen
ETHERNET
page.
NOTE
2 or more simultaneous VNC connections are not possible. i
When EXTERNAL Control has been set to LOCK on the Lock Setup screen, display i
is possible but operation is not when using a VNC viewer application.
Changing any settings on the REMOTE SETUP screen of the ETHERNET page will
i
also end any active VNC connection.
For information about VNC viewer application that have been confirmed to work
i
properly with this unit, please contact TASCAM customer support.
When files are being transferred by FTP or when the system sampling frequency is
i
88.2 or 96 kHz, VNC viewer application display and operation will not be smooth.
Changed pop-up messages
Old message New message Details and responses Remarks
CFn not recommended format for
Recording/Playing.
When media loaded:
CFn formatting not optimal for
Recording/Search.
When starting recording:
CFn formatting not optimal
for Recording.
Since the media was not formatted by
this unit, normal recording and search
operations cannot be guaranteed.
Format the media with this unit before
use.
n = 1 or 2
This appears when the card is formatted
with a cluster size that is smaller than
the standard of this unit.
CFn not recommended for
Recording/Playing.
(not UltraDMA)
When media loaded:
CFn not recommended type
for Recording/Search.
(not UltraDMA)
This CF card does not meet the speci-
fications required by the system, so
normal recording/playback operations
cannot be guaranteed.
n = 1 or 2
New popup messages in HS-4000 V1.22
Message Details and responses Remarks
Cannot Change Now
Currently ON AIR
Changes cannot be made when on air.
Cannot Copy.
Destination Project is
different Fs.
The copy destination sampling frequency is different so copying
is not possible.
Cannot Copy.
Selected Take already exist
in Copy destination.
The selected take already exists in the copy destination so
copying is not possible.
Cannot set Mark point
in ON AIR Mode.
Marks cannot be set when in on air mode.
Cannot use Bridge file
because it is illegal.
The bridge file is not formatted correctly, and could not be
understood.
Capture BC$ Time to ALL?
BC$STANDBY -> Start
BC$END -> End
Confirm changing all entries to the BC$STANDBY/BC$END mark
time range.
Capture BC$ Time?
BC$STANDBY -> Start
BC$END -> End
Confirm changing to the BC$STANDBY/BC$END mark time
range.
CFn(vvvvvvvv)
Fs : fs
USED SIZE : u
FREE SIZE : f
TOTAL SIZE : t
This shows information about the CF card when in on air mode
n = 1 or 2
vvvvvvvv = volume level
fs: the current sampling frequency setting
u: used capacity
f: unused capacity
t: total capacity of CF card
Change Fs to nnkHz?
Confirm changing the system Fs to the shown sampling
frequency.
nn: sampling frequency
Confidence Monitor is not available
with current Fs/Rec CH settings.
The sampling frequency or recording channel settings prevent
the use of confidence monitoring.
Copy n selected Take? Confirm copying selected take(s).
n = number of takes
Takes if n is 2 or more
Copying Take... Take is being copied. "Takes..." when multiple takes are being copied
Directory contents changed
via FTP.
REBUILD required.
REBUILD Now?
The contents of the directory were changed by FTP, so rebuild-
ing is necessary.
EDL Import completed
but there are some wrong regions.
EDL importing has completed, but some regions have problems.